Replacement Wiper Blades for a 2000 Fleetwood Bounder

Question

Question:

I need the type that are held in place with two small set screws. The screws attach the blades to the arm.

asked by: Thane H

1

Helpful Expert Reply:

According to ClearPlus the correct replacement left and right wipers for your 2000 Fleetwood Bounder is # CP77261. Based on your description you would use the saddle fitting to attach the new blades.

expert reply by: Michael H

1

click to enlarge

Answer 1

The main difference between the Voyager Rear Camera part VCMS155B and the Voyager Rear Camera part #VCMS17B is that the latter has a smaller viewing angle, 131 degrees compared to the former which has a 155 degree viewing angle. They will both work…

view full answer...

Answer 2

The WVOM43 monitor you have now is the 1st generation system and, as you said, wireless. The #VCMS17B is a wired camera so it is not directly compatible. 1st generation parts are no longer being made, and the newer generation is not backwards…

view full answer...

Answer 3

Thank you for the pictures and information provided. While the Atwood 75721 motor and gear boxes are discontinued, we do have a gear box that will work with your Atwood 75721 motor and landing gear. - Replacement Gearbox for Venture Aluminum Electric…

view full answer...

Answer 4

The Replacement Fan Motor Assembly Kit for Fan-Tastic Vent Roof Vent Fans #FVK8017-00 will work as a direct replacement for your Create A Breeze 3-speed fan. I've attached a photo with the measurements to give you the exact dimensions in case you…

view full answer...

Answer 5

The closest option we have in size to the High Pointe EM925RWW is the High Pointe Standard RV Microwave #HP59ZR. This microwave is 19-1/8" wide x 11-1/2" tall x 14-13/16" deep. The trim kit that comes with these units is approximately…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Replacement Wiper Blades for a 2000 Fleetwood Bounder

Product Page this Question was Asked From

Continue Researching