Would Ramp Hinges PLR1902 Work as Replacement for H and H Trailer

Question

Question:

I have an 05 14foot h and h enclosed trailer that the rear ramp hinges rusted off, there are 3 of them and the ramp is rated at 4000 lbs would the hinges you have available work? Thanks

asked by: Rick

0

Expert Reply:

The ramp hinges part # PLR1902 don't have a specific weight rating, but I can tell you that by the sheer size of these things and their steel constructions that three of them would be just fine for a 4,000 lb rated ramp.

expert reply by: Jameson C

0

click to enlarge

Answer 1

Hi Tim; the #PLR1902 can definitely be used on your 6 x 9 dump trailer. They don't have an exact capacity but will be able to handle whatever you're doing. Since they're similar to what you have now that would make them a great fit. The…

view full answer...

Answer 2

The Ramp Door Hinge #PLR1902 does require welding of both portions. The tab gets welded as you stated to one side and the outside cylinders get welded to the opposite side. I've attached a couple pictures to assist.

view full answer...

Answer 3

If your trailer is brand new and recently purchased ideally you would return to the dealer to have the ramp corrected. The amount of misalignment you describe seems excessive for a brand new trailer. If the trailer is parked on uneven ground the ramp…

view full answer...

Answer 4

Appreciate the photo, and while I couldn't find any reference to part number I550-000, we do have a possible option for the ramp door hinge: - Ramp Door Hinge #PLR1902 The #PLR1902 has a pin that measures 8-3/16" long x 1" diameter and…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 12

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Would Ramp Hinges PLR1902 Work as Replacement for H and H Trailer

Product Page this Question was Asked From

Continue Researching