Installation of Ramp Door Hinge Polar 1902

Question

Question:

Question about part # PLR1902. I can see on video the plate is welded to project, but doesnt show attach procedure of the other stationary side, round piece. I assume it is also attached with a weld. Correct? Thanks

asked by: Buddie P

1

Helpful Expert Reply:

The Ramp Door Hinge # PLR1902 does require welding of both portions. The tab gets welded as you stated to one side and the outside cylinders get welded to the opposite side. I've attached a couple pictures to assist.

expert reply by: Jason S

1

click to enlarge

Answer 1

Appreciate the photo, and while I couldn't find any reference to part number I550-000, we do have a possible option for the ramp door hinge: - Ramp Door Hinge #PLR1902 The #PLR1902 has a pin that measures 8-3/16" long x 1" diameter and…

view full answer...

Answer 2

Hi Tim; the #PLR1902 can definitely be used on your 6 x 9 dump trailer. They don't have an exact capacity but will be able to handle whatever you're doing. Since they're similar to what you have now that would make them a great fit. The…

view full answer...

Answer 3

The ramp hinges part #PLR1902 don't have a specific weight rating, but I can tell you that by the sheer size of these things and their steel constructions that three of them would be just fine for a 4,000 lb rated ramp.

view full answer...

Answer 4

Thanks For the photos of your hinges. That helps a lot when we are trying to find something for a customer. I have attached a photo of a hinge, part #PLR1902 that may work for you. You can check out the photo and see the dimensions for the hinge. The…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Installation of Ramp Door Hinge Polar 1902

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching