Possible Hub Recommendation to Fit Mobile Home Axle with Bearings 25580 and 102949

Question

Question:

I have a mobile home axle that uses a lm102949 inner bearing, which has a 1.781 id as opposed to the more common 25580 1.75 id. Outer is 1.25 and seal is standard/common. Do you have any hub swap solution or suggestions for bearing combo to get to the same dimensions on the race to fit the Dexter hub? Thank you.

asked by: Ray

0

Expert Reply:

There is a slight chance you have number 42 spindle dimensions on your mobile home axle.

Measure the diameter of your spindle to get the exact dimensions of where the bearings and seals ride. If the bearing dimensions are 1.74 and 1.25 and the seal diameter is 2.24 then you are in luck.

A hub like part # AKIHUB-865-7-1-K would fit. I attached a link to a page that has all the fits as well.

expert reply by: Jameson C

0

Answer 1

The Kodiak Disc Brake Kit #K2R712E is designed to work on idler hubs exactly like the Trailer Hub Assembly #8-231-9UC1-EZ that you referenced. These parts are totally compatible with each other and I can assure you that the spacing between the…

view full answer...

Answer 2

The #TRU37FR EZ Lube or the #TRU57FR standard spindle is compatible with the #AKIHUB-865-7-1-K hub you mentioned. These spindles are compatible with a 5200, 6000 or 7000 lb capacity axle, the axle capacity will depend on the bearing set used. The hub…

view full answer...

Answer 3

Hey Charlie, thanks for reaching out! For that exact brake assembly you'll need part #23-105. The Kit #23-105-106 you found has both the Left #23-105 and the Right #23-106 brake assemblies. Usually when you replace something on one side of the…

view full answer...

Answer 4

If you can read me the serial number on the axle I can then call the manufacturer, Dexter, and find out the weight capacity but if not you can measure the diameter and use the chart below to determine axle capacity. The "P16" is the plant…

view full answer...

Answer 5

Physically? Yes. Legally? Maybe. Assuming your axle is a 3,500, which is by far the most common, you can remove the 10" brakes from the backing plate and replace the hub and drum assembly with an idler hub like #AKIHUB-545-35-K. With that said…

view full answer...

Answer 6

Though we do not sell complete conversion kits with all the necessary parts to convert to disc brakes, we do have all the parts to put it together for your 10,000 pound Dexter axle we have a couple options. The first option is the Kodiak Disc Brake…

view full answer...

Answer 7

Hey Will, The problem with the tire size is that if you go too large the wheels are going to rub the trailer. Timbren having done the math already and listing the maximum as 35 x 12.5 x 20 lets us know that you'd really need to make some serious…

view full answer...

Answer 8

It appears that the HydraStar Disc Brake Kit #HSE7K-T1 is the correct kit for your 2021 Vanleigh Vilano 320GK. To verify this you can find the axle serial numbers and send that information to me so I can verify all the components are correct.…

view full answer...

Answer 9

The Pacer Performance Hi-Five Truck Cab Lights are available in both red part #PP20-215 and amber part #PP20-205. The red cab light has a clear incandescent bulb housed in a red cover whereas, the amber set has an amber lens and amber incandescent…

view full answer...

Answer 10

The only way to confirm whether or not the Trailer Idler Hub Assembly for 7,000-lb Axles - 8 on 6-1/2 #AKIHUB-865-7-2-K will fit your mobile home axles is to pull a hub on both axles and check the bearings and grease seal to see if the part numbers…

view full answer...

Answer 11

You will want part #TRU57FR for your standard spindle that is compatible with the hub #AKIHUB-655-6-K you mentioned. Another option is #TRU67FR which is an agricultural spindle to fit the 6k capacity. The hub compatible with this spindle is the…

view full answer...