Brake Controller Recommendation and Install for a 2007 Chevy New Body Silverado

Question

Question:

I have a 2007 new body style silverado. Just want to make sure the part 3016 and brake controller that goes with it is a good fit for my truck? Thank you,

asked by: Dave R

0

Expert Reply:

For your 2007 Chevy Silverado there isn't a brake controller install port under the dash so the # 3016 would not be the correct harness to use. The wiring for a brake controller is present, but it is not a port or connector. It is 4 blunt cut wires that will allow you to wire a brake controller to.

If you check out the install video I attached you will see our best selling P2 part # 90885 brake controller being installed in a 2007 Chevy Silverado just like yours. I also attached a help article on how to do this as well that will walk you through the entire process.

For a brake controller I would recommend the Prodigy P2 Brake Controller part # 90885. This is our best selling brake controller because of how well it works and how easy it is to setup. This is a proportional brake controller that senses the amount of braking the tow vehicle is applying and applies a proportionate amount to the trailer brakes.

expert reply by: Jameson C

0

Answer 1

I would be happy to help! On your 2007 Chevrolet Silverado New Body Style there will be four wires underneath the dash that the controller will get connected to, as that year truck did not include a factory trailer brake controller port. The four…

view full answer...

Answer 2

I recommend going with the Tekonsha Prodigy P2 Trailer Brake Controller, #90885, for your 2007 Silverado 1500. The P2 activates trailer brakes in proportion to your vehicle's braking action and automatically adjusts the trailer's braking…

view full answer...

Answer 3

When installing an aftermarket brake control into a truck that is equipped with a factory Integrated Trailer Brake Control (ITBC), you will have to make the following connections. The 2007 (new body style)-current models have four or five blunt-cut…

view full answer...

Answer 4

The fact that your trailer brakes will not lock up at 20-25 mph speed does not necessarily indicate a problem with the brake controller. The best way to isolate the problem is to apply a circuit tester to the wires leading into one of the trailer…

view full answer...

Answer 5

I am sure there is a way to install an OEM integrated brake controller on your 2007 Chevy Silverado. But I would strongly recommend you go with an aftermarket brake controller because they end up costing less and perform much better. For a brake…

view full answer...

Answer 6

Sounds like the guy who you had install the brake controller may have been in over his head (no disrespect). But we can help! Your new body style 2008 Chevy Silverado did come with wires under the dash for wiring up a brake controller. If there were…

view full answer...

Answer 7

There is a usual suspect here. Have a helper step on the brake pedal while you stand at the rear of the truck. Is the third brake lamp working? The Silverado gets its brake signal for the tow package from the third stop lamp circuit. Open the…

view full answer...

Answer 8

When you don't have a trailer hooked up to your 2007 Silverado, the 5 o'clock pin where the brake controller output is, should not have any power until you put a draw on that wire with your test light like circuit tester #PTW2993. As soon as…

view full answer...

Answer 9

Based on your concerns the CIPA towing mirrors, #CM10900, are the best option for your 2012 GMC Yukon XL. They have minimal hardware, they would be the best out of the options in terms of keeping the stock mirror protected, and they are made with…

view full answer...

Answer 10

Exactly what the term "tow package" means varies a lot between car makers, vehicle models and model years. Sometimes the term refers to a trailer hitch, heavy-duty suspension and fluid coolers, wiring harnesses, brake controller or all of…

view full answer...

Answer 11

I have another option for you, but your 2007 Chevrolet Silverado 2500HD Classic has a factory trailer brake controller port so there is no need to cut any wires. To replace your current controller with the Curt Assure Trailer Brake Controller with…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Brake Controller Recommendation and Install for a 2007 Chevy New Body Silverado

Featured Help Information

Miscellaneous Media

Continue Researching