Shortest Available 2-Inch Ball Mount

Question

Question:

Whats the shortest hitch ball mount distance you sell for a 2in? From mounting hole to hitch ball?

asked by: Robert S

0

Expert Reply:

You can see all fixed 2-inch ball mounts by clicking on the linked page.

The shortest of these is the Curt Ball Mount # C74WR. This aluminum ball mount measures 8-1/2-inches from the center of the hitch pin hole to the center of the ball hole. It offers either 2-inches of drop or 1-inch of rise. Tow rating is 8K and tongue weight is rated at 800-lbs. A video is linked for you.

expert reply by: Adam R

0

Answer 1

According to the owner's manual for a 2018 Audi Q5, the maximum tongue weight capacity for the vehicle is 440 lbs. The factory trailer hitch is more than likely rated higher than this but that is a rather moot point as the vehicle is lower and…

view full answer...

Answer 2

With the Curt Triflex part #C24VV and the Curt Adapter part #C51522 you will have all you need to successfully install your controller. I have linked a video for you showing the operation of the controller. Check it out to familiarize yourself with…

view full answer...

Answer 3

Both the Curt Spectrum #C51170 and the Redarc Tow-Pro Elite #RED44FR are excellent brake controller options for your 2016 Audi Q5 but in comparison I recommend going with the Tow-Pro Elite over the Spectrum. Although both controllers can be used as…

view full answer...

Answer 4

The mounting hole dimensions of the Brophy Rope D-Ring Tie-Down Anchor #SS15-C that you referenced is 7/16 inch by 7/16 inch. Best option would be to use a carriage bolt with shoulders that match that dimension and you'd be set.

view full answer...

Answer 5

Hey Marc, yes the locking hitch pin part #WS54CR will work with the stacked Replacement Shank for Gen-Y Adjustable Ball Mount #325-GH-306 you are interested in but since would prefer the hitch pin locks to be keyed alike a better option would be the…

view full answer...

Answer 6

3/4 inch plywood will be fine as long as it is properly installed to the floor of your trailer and your motorcycle isn't a 1,200 lb monster like a Goldwing. I would recommend using an anchor plate below the plywood like the part #e96RR.

view full answer...

Answer 7

For a D-ring tie down anchor with a similar capacity and doesn't require a recessed mount we have the part #SS15-C which has a 1,600 lb capacity. I attached a review video for this anchor for you to check out as well.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Shortest Available 2-Inch Ball Mount

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching