Height of the B and W Flat Bed Fifth Wheel Hitch part # BWRVK3050

Question

Question:

I see that this unit has a fixed height. May I ask what that height is?? Thank you.

asked by: Scott

1

Helpful Expert Reply:

The B and W Flat Bed Fifth Wheel Hitch part # BWRVK3050 will set 10-1/2 inches above the deck height of the flat bed truck it is installed in.

I attached a review video for this hitch for you to check out as well.

expert reply by: Jameson C

1

click to enlarge

Answer 1

The base dimensions of the B and W Companion Flatbed Gooseneck-to-5th-Wheel Trailer Hitch Adapter #BWRVK3050 is 18 x 18-inches and will install it in an opening that measures 20 x 20 x 4-inches deep. The recessed opening cannot be more than 4-inches…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 7

Hey Matt, Furrion typically has 4 wires running to their thermostats and the Chill Cube Thermostat #LC74DX is no exception. The harness you see with the thermostat would plug into the Chill Cube's controller and has 4 wires to extra wire to to…

view full answer...

Answer 8

Hello Joe, Thank you for reaching out! The Power Mountain Tallboy Off-Road Bottle Jack - 11-5/16" to 27-1/16" Lift - 12 Tons #PM94FR does have the capacity you’d need, but since your fifth wheel’s frame sits about 25" off the ground,…

view full answer...

Answer 9

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 10

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the easiest…

view full answer...

Answer 11

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 12

Hey Tom, congrats on the new truck! Typically when we hear that someone has the OEM tow prep package they mean the puck system. This is going to be five circular holes built into the bed of your Ram truck and is by far the best way to attach a 5th…

view full answer...

Height of the B and W Flat Bed Fifth Wheel Hitch part # BWRVK3050

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching