Recommended Replacement Inner Slide For Titan 10 Actuator

Question

Question:

I have attached a picture of the part I need. Is this the same? There are no pics on the web page.

asked by: Jay

0

Expert Reply:

You are correct. The Inner Slide Assembly, part # T1608700317 is the replacement you need for your Titan 10 actuator. Thanks for the photo of the slide you have. This helps when searching for the correct replacement parts.

The T1608700317 is painted and is a weld-on inner slide. I have attached a photo of this slide assembly you can check out.

expert reply by: Jeffrey L

0

click to enlarge

Answer 1

Thanks for the pictures! To replace the master cylinder in your Dico Model 10 actuator you are going to want to use the Replacement Master Cylinder Assembly for Titan Model 10 and Model 20 Brake Actuators item #T2374600. This master cylinder is…

view full answer...

Answer 2

It's hard to tell which cap you need exactly from the picture but I measured the caps we have that might work for you. Part #T4480701 for Titan Model 60 actuators measures 1-1/4 inches at the threads like you previously saw. Part #T4830601 for…

view full answer...

Answer 3

If the master cylinder you need is the part #T2374600 that would indicate that you have a Model 10 actuator like the part #T4750620. Which normally this bolts to the trailer frame. The picture you submitted doesn't quite show the coupler so I…

view full answer...

Answer 4

Replacement master cylinders will be brand specific, so they cannot be mixed and matched. As an example, the Titan master cylinder #T2374600 will only fit their Model 10 and Model 20, and the Demco master cylinder #5650 will only fit their drum…

view full answer...

Answer 5

I have attached for you below an exploded parts breakdown of the Titan/Dico Model 10 Surge Brake Actuator. In regards to the Replacement Top/Bottom Bearing part #T1020900 and Replacement Side Bearing part #T1242700, these work to help stabilize the…

view full answer...

Answer 6

You can replace the inner slide of your Titan Model 10 actuator with the Replacement Inner Slide Assembly w/ 2-5/16" Coupler for Titan Model 10 Brake Actuators #T2478300317. You will also need to replace the slide bearings with the Bearing - Top…

view full answer...

Answer 7

Yes, we do carry the Titan Inner Slide Assembly for Model 10 Titan Actuators as part #T1608700317. It is also listed under the part number 068-050-00 and 1608700317 but they are all the same.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Recommended Replacement Inner Slide For Titan 10 Actuator

Product Page this Question was Asked From

Continue Researching