Where Do the Rubber Bearings Go On the Titan/Dico Model 10 Surge Brake Actuator
Updated 12/19/2019 | Published 12/18/2019 >
Products Featured in This Question
Question:
Are we sure that all Titan \ Dico 10 s have the rubber bearing rubber bearing t1020900 I did not find one when I pulled mine apart. Also not clear on where the rollers go. I have two rollers, its obvious the go on the pin that the bigger eye of the shocks goes thru. Do the rollers go to the outside of the shocks? does this zerk fitting T0144901 fit in the Front Roller Bolt for Titan Model 10 Brake Actuator
asked by: Tom
Helpful Expert Reply:
I have attached for you below an exploded parts breakdown of the Titan/Dico Model 10 Surge Brake Actuator. In regards to the Replacement Top/Bottom Bearing part # T1020900 and Replacement Side Bearing part # T1242700, these work to help stabilize the inner slide inside the outer case and would have been installed on all models. There should be a total of six for the top/bottom and eight for the sides. In regards to the Replacement Rear Roller part # T0829100, these sandwich the upper Replacement Shock part # T1242600. The Replacement Grease Zerk part # T0144901 gets installed on the Replacement Front Roller Bolt part # T0828800 per the diagram below.
If you need any other replacement parts for the Titan/Dico Model 10 Surge Brake Actuator please just let me know.
Product Page this Question was Asked From
Replacement Shock for Dexter Model 6 and 10 Brake Actuators
- Accessories and Parts
- Brake Actuator
- Disc Brakes
- Hydraulic Drum Brakes
- Shocks
- Dexter
more information >
Continue Researching
- Search Results: 72~80
- Search Results: 14125a
- Shop: Replacement Key for etrailer Trailer Tongue Tool Box - Key Number CH508 - Qty 1
- Search Results: accessories and parts
- Search Results: clevis slip hook
- Search Results: qt765
- Shop: 7-Leaf Slipper Spring w/ Hook End for 8,000-lb Trailer Axles - 26-5/8" Long
- Search Results: 2 speed square jack
- Shop: Bearing for Dexter Model 6 Actuator
- Shop: Replacement Inner Slide Assembly w/ 2-5/16" Coupler for Dexter Model 10 Brake Actuators
- Search Results: plr1904
- Shop: Bearing - Top & Bottom - for Dexter Model 10 Actuators
- Shop: Equalizer for 2-1/2" Wide Slipper Springs - LH or RH - 24-7/8" Long - 1" Center Hole
- Shop: Replacement Shock for Dexter Model 6 and 10 Brake Actuators
- Video: An In-Depth Look at the Bearing
- Video: Titan Brake Actuator T1608400317 Review
- Q&A: Recommended Guide-Ons That Stick Out 24 Inches From Either Side Of Trailer
- Video: In-Depth Review of the Replacement Shock for Dexter Model 6 and 10 Brake Actuators
- Article: Best Boat Trailer Jacks
- Shop: Trailer Wiring
- Article: Boat Trailer Guides: Which are the Best?
- Q&A: Solution for Needing New Master Cylinder 1027100 and Damper for Titan Model 6 Actuator
- Q&A: Solution for Banging During Starts and Stops with Titan Model 6 Actuator on Trailer
- Video: Complete Breakdown of the Bearing for Dexter Model 6 Actuator
- Video: Titan Brake Actuators with Reverse Lockout Replacement Solenoid Valve Installation
- Q&A: How to Gauge Height of Guide-Ons for Boat Trailer
- Q&A: How to Install 75 inch CE Smith Post-Style Guide-Ons to 2x6 Boxed Trailer Frame
- Video: Review of the CE Smith Post-Style Guide-Ons for Boat Trailers
- Video: Replacement Damper Pin for Dexter Model 6 Brake Actuator Spec Review
- Q&A: Suggested Replacements for Titan Coupler and Brake Calipers


