Screw Recommendation for Installing Trailer Roof Vent # 9106

Question

Question:

What length of screw do you recommend if the trailer is sheetmetal thickness. More concerned that I will cover them correctly with the 2756 trim piece. Thx

asked by: Drew M

0

Expert Reply:

The recommended screws for installing the part # 9106 that you referenced is the # 31071. This would work well on a sheet metal trailer wall/roof.

The garnish part # 2756 would then fit over them just fine.

expert reply by: Jameson C

0

Answer 1

For the hydraulic Level Up system you have on your 2018 Montana the replacement jack legs for all positions according to Lippert is the part #LC36VR.

view full answer...

Answer 2

Hey Dennis, The bracket the mounts to the trailer wall would need to be installed at the factory and unfortunately isn't an option aftermarket. These are relatively new so I'm assuming after enough people complain to Lippert they'll start…

view full answer...

Answer 3

Yes, the Progressive Dynamics Inteli-Power RV Converter and Smart Battery Charger #PD9280A would be an exact replacement for your PD9280 converter. If you weren't just going to replace it and were going to troubleshoot the issue I recommend…

view full answer...

Answer 4

Hey Mike! Thanks for all the information! The Advent Air Replacement RV Air Conditioner for Dometic Setup w/ Start Capacitor item #ACDOM150 is designed to plug straight into your Dometic air distribution box so you will still be able to use your…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

Hey Lars, welcome back! I can indeed confirm that the Furrion Variable Speed Chill Cube air conditioner with a heat pump is indeed really happening. They are currently available for order (02/04/26) and will be shipped out towards the middle of next…

view full answer...

Answer 12

Sure, I can help with that. I can see why the fitment notes are confusing. For a 2012 Toyota Tundra with the factory tow package and factory 7 way connector, you'll want a brake controller that plugs into the factory brake controller port under…

view full answer...

Screw Recommendation for Installing Trailer Roof Vent # 9106

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching