How to Measure a Trailer Hub or Dust Cap to Find the Right Replacement Dust Cap
Updated 04/21/2020 | Published 09/12/2015 >
Products Featured in This Question
Question:
I have a golf cart trailer that I turned into a utility trailer. I just finished the trailer up and I have notice that my new dust cap fell off. Is there any way of measuring the old dust cap that I have that I replaced with the new. I really dont want to take the wheel off again.
asked by: Kevin
Expert Reply:
You can measure either the outer diameter of the part of the dust cap that fits into the hub OR the inner diameter of the hub where the dust cap goes using calipers such as # PTW80157. Calipers are needed because the measurement has to be as accurate as possible.
I also might be able to figure it out based on the outer bearing number which you should be able to see without taking the hub off.

Brandon C.
4/19/2020
Hello I measured my dust cover at 1.775 with digital calipers. I need two for my boat trailer and was hoping to find some bearing buddies.

Product Page this Question was Asked From
Grease Cap, 1.988" OD Drive In - Qty 2
- Trailer Bearings Races Seals Caps
- Caps
- Standard Grease Cap
- 1.99 Inch O.D.
- 1.99 Inch
- 2000 lbs Axle
- 2200 lbs Axle
- 2500 lbs Axle
- 3000 lbs Axle
- 3500 lbs Axle
- TruRyde
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Search Results: castle nut
- Shop: Kodiak 10" Rotor - 5 on 4-1/2 - Dacromet - 3,500 lbs
- Search Results: bearing protector grease cap trailer bearings races seals caps
- Search Results: dust caps
- Shop: Kodiak Ceramic Brake Pads - 3,500 lbs to 6,000 lbs
- Search Results: wheel bearing dust cap
- Search Results: wheel bearing caps
- Search Results: trailer wheel bearing
- Shop: Trailer Wheel Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Shop: Grease Cap, 1.99" OD EZ Lube Drive in with Plug - Qty 2
- Search Results: trailer bearings races seals caps
- Q&A: Replacing Older Tie Down Engineering 46210 and 46845 Trailer Hubs
- Shop: Bearing Buddy Bearing Protectors - Model 2047A w/ Auto Check - Chrome Plated - Qty 2
- Q&A: How to Measure a Trailer Hub for the Correct Size Grease Cap
- Shop: Dexter Bearing Kit w/ Cap for 1-1/16" to 1-3/8" Tapered Spindle - Bearings L68149/L44649
- Shop: Dexter 10" Hub-and-Rotor Assembly - 5 on 4-1/2 - Zinc - 3,500 lbs
- Video: Trimax Class V Universal Anti-Rattle Clamp Details
- Shop: Lift Assist
- Q&A: Looking for Grease Cap With OD Slightly Larger than 1.98 Inches
- Shop: Windshield Covers
- Q&A: Can I Use the MORryde Add-A-Step with the Lower Hand Rail Kit on My MORryde Steps?
- Shop: Suspension Enhancement
- Video: All You Need to Know About the Kodiak Ceramic Brake Pads
- Video: All About the Bearing Buddy Bearing Protectors-BB2240
- Q&A: Will Bearing Buddies Prevent Water from Getting into Hub
- Q&A: What is the Hub Bore Size
- Shop: Trailer Hitch
- Video: The Low-Down on the Grease Cap, 1.99" OD EZ Lube Drive in with Plug
- Video: Demco eZ-Latch A-Frame Trailer Coupler Comprehensive Review
- Video: Feature Breakdown: Plastic Stem and Rubber Socket Door Holder


David N.
2/11/2020
MY hub measured 1.9996. Do I use a 2.0 cap or what size is correct?