Trailer Hub Recommendation that has Inner Bearing L68148 and Outer Bearing L44649

Question

Question:

Which hub to purchase its 5 lug x 4.5inch bolt circle using an inner bearing L 68148 and an outer bearing 44649

asked by: Eric R

0

Expert Reply:

The trailer hub part # 84545UC1-EZ would be the correct trailer hub you would need as it uses an inner bearing of # L68149 and an outer bearing of # L44649 and has the bolt pattern 5 on 4-1/2 inches.

expert reply by: Jameson C

0

Answer 1

The #L68149 bearing you mentioned is most commonly used with the #L44649 outer bearing, but it is sometimes used with the #LM67048 outer bearing, as well. If you can't read the reference number of your outer inner bearing, you can always use a…

view full answer...

Answer 2

If you look at the outermost part of the spindle on your axle there will be what is called a grease zerk or grease gun fitting. It will look like a tiny round ball which is where you can attach a grease gun to grease your spindle. If your spindle has…

view full answer...

Answer 3

Thank you for the pictures! It looks like you've got some sort of square drop axle on your trailer and if you can't find an identifying sticker, I can still help you figure out what you've got so that you can make the swap to electric…

view full answer...

Answer 4

You will have to replace the spindle. Grooves that can't be taken out with emory cloth will eventually cause new bearings to fail which will leave you stranded with a locked up wheel most likely. To replace a spindle, the old one would need to be…

view full answer...

Answer 5

Trailer bearings can fit pretty tight to the spindle, but they would not ever need to get pressed on. They should not be so tight that you have to really pound on them to fit but they can require a little bit of effort to get them to slide onto the…

view full answer...

Answer 6

We do have the following replacement spindles that will fit on your axle. #84 Spindle for 3,500-lb Trailer Axles - 2" Diameter #TRU24FR #84 Spindle for 3,500-lb Trailer Axles - 1-3/4" Diameter #TRU84FR #84 Spindle for 3,500-lb Trailer Axles…

view full answer...

Answer 7

Trailer spindles are welded directly to the axle so to remove one it just needs to be cut off completely using a torch or saw. Then to replace the spindle such as with the EZ Lube #TRU37FR that you were looking at it's extremely important that it…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Trailer Hub Recommendation that has Inner Bearing L68148 and Outer Bearing L44649

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching