Will a Curt Shank Work with a Reese Weight Distribution System

Question

Question:

Is this Curt shank compatible with the Reese SC 1200 lb WD Head?

asked by: Jerry R

0

Expert Reply:

Yes, the Curt weight distribution shank # C17123 can be used with a Reese weight distribution head. Both have 3/4 inch diameter holes spaced 1-1/4 inches apart on center.

expert reply by: Michael H

0

Answer 1

I recommend the Reese Titan weight distribution shank #RP54977 because it has a 5-3/4 inch maximum drop and 8-1/4 inch rise. The weight distribution head can be mounted so it has a drop of approximately 3 inches. The tongue weight is 1,700 pounds and…

view full answer...

Answer 2

Hey Allie. The shank measures 2-1/2" wide on the Curt Weight Distribution Shank item #C17132. It's designed to fit 2-1/2" x 2-1/2" trailer hitches. The vertical part is 2" wide and works with most weight distribution systems.…

view full answer...

Answer 3

Hello Phil. It does sound like your 1,200 lb bars are too heavily rated for your trailer. I would be looking at something more like 600-800 lb range for your trailer. Something like the Reese Strait-Line Weight Distribution System #RP66073 would be…

view full answer...

Answer 4

Hello again, Phil. Out of those two options I definitely recommend the Reese Dual Cam II #RP65FR with the no-drill frame brackets. In my experience, any WD system that uses no-drill L-brackets that bolt to the frame is going to be much easier to set…

view full answer...

Answer 5

I spoke to Fastway and the ball holder from the Flash Solid Steel HD Adjustable 2-Ball Mount part #FA49-00-5925 won't work on a weight distribution shank as there would be too much play. That said, I do have an option for you which I have…

view full answer...

Answer 6

Changing the placement of the cam arm assembly on Reese Strait-Line Weight Distribution System #RP66130 by the 2-inches you suggest may reduce the effectiveness of the system. The system's capacity to redistribute the trailer tongue weight…

view full answer...

Answer 7

The Reese Steadi-Flex Weight Distribution System #RP66560 does not require any additional lubrication other than greasing the coupler. The only other maintenance that is necessary keep the system clean and rust-free so it will be much less than what…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Will a Curt Shank Work with a Reese Weight Distribution System

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching