Availability of Lock for Curt Trailer Hitch Anti-Rattle Kit # F-315

Question

Question:

Do you sell a lock for this part

asked by: Alberto

0

Expert Reply:

An add-on lock is not available for the Curt Trailer Hitch Anti-Rattle Kit # F-315 but we do offer locking hitch pin devices for 1-1/4" accessories such as #e98879 that work with any hollow-shank ball mount or accessory. However, the # e98879 is not an anti-rattle device, only a hitch lock.

expert reply by: Adam R

0

Answer 1

We have a hitch that will fit your 2023 Infiniti Q50 Sport and allow you to use your bike rack with a 1-1/4" shank. - Draw-Tite Sportframe Trailer Hitch Receiver #24931

view full answer...

Answer 2

The Curt Trailer Hitch Receiver part #C11407 which is a fit for a Infiniti Q50 does not require a support strap. This was once required for all Curt trailer hitches but has since been removed. In regards to using a 1-1/4" to 2" adapter like…

view full answer...

Answer 3

The trailer hitches with the highest capacity for your 2019 Infiniti Q50 is the Draw-Tite Trailer Hitch Receiver #24931 and the Curt #C11407. These are both class I which has a 2,000 lb towing capacity and 200 lb tongue weight capacity. I should note…

view full answer...

Answer 4

Realistically the Curt Trailer Hitch Receiver #C11407 and Draw-Tite Trailer Hitch Receiver #24931 that fit your 2020 Infiniti Q50 have only very slight differences, but I would go with the Curt for a couple different reasons. One of which is that the…

view full answer...

Answer 5

I have a solution for you, however, Yakima's SKS cores are only compatible with Yakima's products. You can't cross use them Yakima does offer an SKS compatible hitch lock for its bike racks as part #Y07235 that is compatible with all…

view full answer...

Answer 6

Both the Curt Trailer Hitch Receiver #C11407 and Draw-Tite Sportframe Trailer Hitch Receiver #24931 that are confirmed to fit your 2021 Infiniti Q50 are very similar both in how they attach to the overall construction. We have been able to install…

view full answer...

Answer 7

I assume you are referring the Curt Spare Tire Carrier, part #C31006 and one of the Class I hitches you purchased from us. Both of those hitches have a 200 pound tongue weight capacity. However, if you are using the HTAD adapter, the tongue weight…

view full answer...

Answer 8

It sounds like the anti-rattle hitch bolt in your old Yakima ROC'nGate is causing issues by not tightening up all of the way. Assuming the bolt itself is what is bad you can just replace it with #Y8890200. When it comes to replacement parts for…

view full answer...

Answer 9

You are right, I pulled both the part #Y8890185 and the #Y8780022 from our warehouse and the only difference is the additional flat washer that is in the #Y8890185.

view full answer...

Answer 10

It looks like you need replacement hitch bolt, nut and clip #Y8780022. It fits into a 2 inch or 1-1/4 inch shank to provide anti-rattle capabilities of certain present and discontinued Yakima bike racks including the BigHorn, KingPin, BackSwing,…

view full answer...

Answer 11

For your Yakima Hold Up, the Replacement Spine #8890277 will require the Replacement Hitch Hardware for Yakima HoldUp Bike Racks #8890260. The 1-1/4 inch hardware will not be the correct fit for the larger shank.

view full answer...

Answer 12

We have two different anti-rattle devices that would work very well for you. If the ball mount you're using is hollow, the Let's Go Aero locking anti-rattle hitch pin, part #63232 would work great. The square block and spring would insert…

view full answer...