Troubleshooting Edge Programmer that Wont Power Up When Plugged Into Vehicle

Question

Question:

i have the edge with attitude for a 5.9 diesel, the screen is black. cigarette lighter fuse is good. It works great when plugged into computer. Do I need to send it in or can I fix this?

asked by: Victoria

0

Expert Reply:

The problem you described sounds exactly like a blown vehicle fuse.

Since Dodge changed where the OB2 port gets its power, you will need to check the fuses for either the underhood light or the dome light fuse. If you find a blown fuse that is causing the problem you just need to replace it and you should be good to go.

expert reply by: Jameson C

0

Answer 1

The License Plate Mounting Bracket #AA85-0000 or #XIL-LICENSEP may be able to help you keep the license plate from bending. The both have a 90 degree bend to make mounting easier if your plate is attached to the bottom of a frame.

view full answer...

Answer 2

On the Aries License Plate Bracket #AA85-0000 the two mounting holes on the horizontal top surface are spaced apart on center at 7-1/8-inches. Each hole has a diameter of approximately 5/16-inch.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 10

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Troubleshooting Edge Programmer that Wont Power Up When Plugged Into Vehicle

Continue Researching