Do the Prodigy P2 and P3 Use the Same Install Harnesses

Question

Question:

Currently have Prodigy P2 Controller, will a P3 be compatable will my wiring on my P2? Thanks .By the way, how much r the new P3?

asked by: Paul W

1

Helpful Expert Reply:

The Prodigy P3 part # 90195 would plug right into the harness that your P2 # 90885 installs into. It would be just a matter of unplugging the P2 and plugging the P3 in it's place.

The mounting brackets would be different so you would need to also mount a new one.

The price is attached at the product links.

expert reply by: Jameson C

1

Answer 1

The best brake controller option to go with is one that activates the brakes proportionally instead of time delayed. A proportional brake controller will activate the trailer brakes at the same time and with the same intensity as the tow vehicle…

view full answer...

Answer 2

As far as function goes, the two controllers are actually pretty similar. The primary difference between the two is that the P3 uses what I would call a more user friendly display. Instead of an error code like what's displayed on the P2, the P3…

view full answer...

Answer 3

There are a few differences between the two controllers. The Voyager has been around for a looooooooong time. It uses an internal pendulum to determine how quickly the tow vehicle is braking. In order to operate correctly, this level of the pendulum…

view full answer...

Answer 4

The original Tekonsha Prodigy, part 90185 can use the same Plug-In Wiring Adapter, part #3035-P which is compatible with any of Tekonsha's controllers. In other words, your existing plug will be compatible with the P2. If you have a Prodigy…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Do the Prodigy P2 and P3 Use the Same Install Harnesses

Featured Help Information

Miscellaneous Media

Continue Researching