Removing Wiring Harness Cap to Install # 118491 on 2010 Honda Pilot

Question

Question:

Im having trouble removing the protective cap under the bumper of my vehicle. Its the plug in to which the the actual harness is to plug into. I squeeze the back of the connector and can feel the plug begin to release, but it will not come out. Am I doing something wrong?

asked by: Chris

0

Expert Reply:

There are two tabs on either side of the cap, with the tabs released apply a rocking motion back and forth. You might have to keep at it for a bit, but the cap should come off. Avoid using brute force like pliers, if those tabs are damaged the plug will not be seated correctly when plugged in.

expert reply by: Mike L

0

August D.

4/1/2024

How does one release the two tabs and get them to stay released and pull the cap off? What a stupid setup and why did the vehicle not come with a harness with a tow package?

Mike L.

4/10/2024

@AugustD If you're having difficulty, you could have a friend assist. Have them on the tabs while you remove the cap. We agree, that cap is notorious for being difficult to remove, but you'd need to ask Honda why they designed it thataway and why they didn't equip your Pilot with a Tow Package.

Answer 1

To find out if your 2010 Honda Pilot came with a tow package from the factory, the most certain way is to have a dealer run the VIN. There are some tell tale signs, however, that may lead you in the right direction. If the Pilot has a functioning…

view full answer...

Answer 2

The presence of the plugs on your 2011 Honda Pilot does not mean that they are active. The difference is in how the vehicle is equipped. If the 2011 Honda Pilot did not come with a factory installed 7-Way trailer connector, that means that it is not…

view full answer...

Answer 3

From your picture it looks like the damage is only on that one side so you should still be able to pull the cap off and finish the installation of harness #C56365. There is a little tab right above the white, red, and green wires in your picture that…

view full answer...

Answer 4

The cap on the factory plug on your 2014 Honda Pilot should separate from the plug by lifting up on a tab. You may need a small flathead screwdriver to do so. We do not have a video showing this but looking at the end that plugs into the vehicle it…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Removing Wiring Harness Cap to Install # 118491 on 2010 Honda Pilot

Continue Researching