What Size Socket is needed to Tighten Bolts on Reese Round Bar Weight Distribution Head

Question

Question:

Hi, what size of spanner, socket should I have to unbolt it? Is it 1 3/8? And what is the recommended torque to tighten? Thanks!

asked by: Derrick

0

Expert Reply:

I went out to the warehouse and the large 3/4 inch bolts used on the Reese round bar weight distribution head # RP58112 require a 1-1/8 inch socket or wrench.

For information on torque specs please refer to the instructions I have linked for you.

expert reply by: Michael H

0

Answer 1

Based on the 30-92-XXX partial part number you provided, it sounds like you have Bargman 92 Series taillights. These taillights measure 8-9/16 inches long x 4-9/16 inches wide x 2-1/8 inch thick. I have some options for LED taillights for you,…

view full answer...

Answer 2

I ran out to the warehouse, and pulled one of the #AMAC1 shanks. I found that the distance from the end of the shank that would insert into the hitch receiver to the center of the hitch pin hole is exactly 2-11/16 inches, as you can see in the…

view full answer...

Answer 3

I believe the measurement you are looking for is 7-1/4 inches. I attached a picture that shows this measurement as well as another picture that has some other measurements you may find useful. If you need any other measurements just email me back.

view full answer...

Answer 4

The lights themselves are identical. I reached out to my contact at Bargman who said that the only difference between the Bargman Tail Light Assbemly #30-92-003 and one with the part number 34-92-003 is how it is shipped to the company. One of them…

view full answer...

Answer 5

There is an issue with German vehicles (Audi, Mercedes, Porsche, BMW, Volkswagen, and so on) and trailers with LED lights. The LED trailer lights do not offer enough draw on the system for the lights to work. On a lot of these vehicles you will also…

view full answer...

Answer 6

If the trailer has LED lights then the issue isn't the adapter or the trailer. It is the vehicle. The 2012 Mercedes GL450 and other German vehicles do not work well with trailers that have LED lights. This is because LED lights do not draw enough…

view full answer...

Answer 7

We do have a few options for replacement WD shanks that have a distance shorter than 8 inches from the center of the hitch pin hole to the center of the adjustment holes. The Convert-A-Ball Cushioned Weight Distribution Shank #AMAC1 fits 2 inch hitch…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

What Size Socket is needed to Tighten Bolts on Reese Round Bar Weight Distribution Head

Featured Help Information

Miscellaneous Media

Continue Researching