What Style of Connectors Does the Bargman 7-Way Molded Trailer Wire Connector # 50-67-210 Fit

Question

Question:

Item 50-67-210 Will the plugs on this connecting cable fit both the RV style socket and the vehicle-style socket? In other words, both the 7 pin and the 7 blade sockets? Thanks

asked by: Dick G

0

Expert Reply:

The Bargman 7-Way Molded Trailer Wire Connector # 50-67-210 that you referenced uses a standard RV style 7-way flat connector on both ends. The socket it would fit would look like the part # PK11893.

This style of 7-way is the kind that is very commonly seen at the rear of vehicles and RVs.

expert reply by: Jameson C

0

Answer 1

Do you have a crew cab or a regular cab? Torklift is really particular with their fits but with that last bit of info I should be able to see what solution would work.

view full answer...

Answer 2

I've never heard of or seen a female to female 7-way connector and based off of what you are describing having on your vehicles and looking at I think you need the Bargman 7-Way Molded Trailer Wire Connector item #50-67-210. This cable has a…

view full answer...

Answer 3

Yes, we carry the Bargman 7-Way Molded Trailer Wire Connector #50-67-210 which has a 7-way male connector on both ends and is 8' in length. We also carry adapter cables if you need to go from a 7-way to a 6, 5, or 4-way connection.

view full answer...

Answer 4

Hello Ken, thanks for reaching out. Sounds like you are on the right track here because the type of running boards on your truck do dictate which tie downs to use. You are also correct that you will not be able to use the tie downs from your old 2002…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...