How to Bleed Trailer Surge Brakes
Published 04/23/2015
Question:
once installed how do you bleed brakes
asked by: Phil
Expert Reply:
There are a couple of ways you can bleed a trailer brake system. Titan offers the following instructions, which I have also linked for you, on bleeding the brakes:
Remove the master cylinder cap and fill the reservoir to three quarters full with DOT-3 brake fluid. DO NOT allow brake fluid to contact painted surfaces since it will damage the finish. Wipe up any spills immediately and wash the area with water.
If you choose to manually bleed the system, an assistant makes the job easier. Disconnect the trailer from the tow vehicle and hook the safety chains (NOT the actuator breakaway cable) together to form a loop. The loop should be centered below the actuators coupler.
Place a sturdy board such as a 2 x 4 into the safety chain loop below the coupler. The board should be four feet long or more so it will extend well above the actuator. Position the board to press against the front end of the actuator’s coupler and use it to force the coupler case into the actuators outer housing. This pumps the brake fluid into the trailer braking system. Manually pull the coupler case back to fully extended position and repeat the process.
When the air bubbling stops inside the master cylinder, install a bleeder hose on the bleeder screw of the first wheel cylinder to be bled. Start with the rear axle on tandem axle trailers. Submerge the other end of the hose in a glass container of brake fluid so that air bubbles can be observed. Open the bleeder screw one turn before pushing the coupler case in. When the coupler is pushed completely in, the bleeder screw should be closed to prevent air from being pulled back into the system. Air trapped in the brake lines will greatly reduce your braking efficiency. Repeat this process until no more bubbles are released with each stroke. Be sure to close the bleeder screw securely.
Repeat the bleeding operation at each wheel cylinder. During the bleeding process, replenish the brake fluid so the level does not fall below half full level in the master cylinder reservoir. When bleeding is complete, fill the reservoir to within 3/8 inches of the top. Install the filler cap securely.
There are also vacuum types of systems that you could use but doing it manually is what most people do. I have also included a link to a video that should help.
Product Page this Question was Asked From
Dexter Zinc-Plated Brake Actuator - Disc - 2-5/16" Ball - Bolt On - 8,000 lbs
- Brake Actuator
- Surge Brake Actuator
- Farm Trailer
- Boat Trailer
- Construction Trailer
- Travel Trailer
- Utility Trailer
- Bolt-On
- 8000 lbs GTW
- 2-5/16 Inch Ball Coupler
- 3 Inch Channel Tongue
- Disc Brakes
- No Lockout
- Dexter
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Kodiak Disc Brake Caliper - Dacromet - 3,500 lbs to 6,000 lbs
- Q&A: Will the Kodiak 225 Calipers Be a Direct Replacement for a TDE 46304 Caliper
- Search Results: 84545 hub
- Shop: DeeMaxx Stainless Steel Drive-In Grease Cap w/ Plug - 1.98" Outer Diameter
- Shop: DeeMaxx Stainless Steel Drive-In Grease Cap w/ Plug - 2.45" Outer Diameter
- Shop: Replacement Inner Member for Dexter DX7.5L Actuator - Single Axle w/ Disc - 2" Ball - 7,500 lbs
- Shop: Dexter DX7.5L A-60L Surge Brake Actuator w Electric Lockout - Disc - 2" Ball - Primed - 7.5K
- Shop: Dexter Zinc-Plated Brake Actuator - Disc - 2-5/16" Ball - Bolt On - 8,000 lbs
- Article: How to Bleed Your Trailer Surge Brakes
- Q&A: How the Shock Absorber Works on a Surge Brake Actuator
- Search Results: boat trailer brake actuator
- Search Results: 34043
- Shop: Replacement DeeMaxx Disc Brake Caliper - Maxx Coating - 3,500 lbs to 6,000 lbs
- Q&A: How to Replace the Shock on a Titan Model 10 Surge Brake Actuator
- Video: Comprehensive Review: CE Smith Wobble Roller Retainer Ring
- Q&A: Why Are My Calipers Dragging On My Load Rite Trailer?
- Q&A: How to bleed the brakes on a surge brake actuator on boat trailer
- Q&A: Torque Settings For Wheel Lug Nuts For Boat Trailer And utility Trailer
- Video: All You Need to Know About the Kodiak Ceramic Brake Pads
- Q&A: Troubleshooting Surge Brake Actuator that Won't Release Brakes
- Search Results: boat trailer brake lights
- Search Results: wobble roller
- Search Results: third brake light
- Search Results: trailer brakes
- Article: Trailer Wiring Diagrams
- Shop: Trailer Hitch
- Shop: Trailer Wiring
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Suspension Enhancement
- Article: How to Measure Your Trailer Wheel Bolt Pattern
on Brake Actuator
