Distance Between Mounting Holes of the Bulldog Collar-Lok Channel Mount Coupler # BD028657

Question

Question:

What is the distance between mounting holes center to center on this coupler? Thanks,

asked by: David C

0

Expert Reply:

The Bulldog Collar-Lok Adjustable Channel Mount Coupler # BD028657 that you referenced is designed to fit a channel like the part # BDAC5000300 which has a distance of 2 inches between each mounting hole measured on center.

I attached review videos for both products for you to check out as well.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The Demco Adjust Channel Mount Coupler part #DM07678-95 has a 20k capacity and is designed for 2-5/16 inch hitch balls. Then for a channel to attach it to the part #DM59602 also has a 20k capacity and is 12 inches tall.

view full answer...

Answer 2

I had a similar question as this and spoke to Bulldog and they said that the capacity for their couplers like the part #BD028657 that you referenced can only be guaranteed if the mounting bracket is tight against a channel. If there is a gap you will…

view full answer...

Answer 3

Bulldog Collar-Lok Coupler #BD028287 and similar couplers have a sleeve that constantly puts pressure on the front of the coupler, the part that goes around the ball, so that it cannot come loose. There is also more surface area of the coupler making…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Distance Between Mounting Holes of the Bulldog Collar-Lok Channel Mount Coupler # BD028657

Featured Help Information

Miscellaneous Media

Continue Researching