Stability and Strength of Stromberg Carlson Rail Mate Folding Handrail # AP-101

Question

Question:

Looks like the real is only attached to the base of the steps. How does the rail remain strong at the top and not just bend at that connection point? cant the foot just get kicked out and have the entire rail spun to the side?

asked by: Aaron

0

Expert Reply:

The Stromberg Carlson Rail Mate Folding Handrail # AP-101 does have one attachment point, at an included plate that bolts on to your steps. Please refer to the linked photo showing the bracket. This bracket design allows for easy rail removal.

For a railing like this most of the force on it will be vertical - as when climbing up or down the coach's steps - rather than side-to-side. Certainly it could be possible to swing the railing away from the steps if enough lateral force was applied to it.

expert reply by: Adam R

0

click to enlarge

Marie

1/30/2020

We just bought a Keystone Passport BH. We asked the dealer if we could upgrade the handrail for our kids. We were told there wasnt a handle similiar w/ out having to drill extra holes & were told we should not attempt doing so till after the warranty expires. Question: will adding this handrail void a warranty?

Reply

Jacob H.

2/4/2020

We have a removable handrail that attaches to the fold out steps of the camper # AP-101. The brackets that hold the handrail will bolt to your steps and the rail will simply unfold and slide into place. The folding feature makes it nice for easy storage. When the handrail is not in place you won't even know the brackets are there. This is a great kit that does not involve drilling into your camper and will allow your kiddos to safely enter and exit.

Reply

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

Hey Jay! You do not need to completely reset the air in the air bag when you remove the #SHK23VR. However, you will have to reduce the air pressure slightly so it isn't clamped on tight. All you have to do is push in on the air valve and the…

view full answer...

Answer 4

Hey Jairo. So we do not offer a direct replacement for the Norcold N611, but we do have a good replacement option for you. It really comes down to what will fit in your cutout space. Take a look at the Norcold RV Refrigerator w/ Freezer - 8.2 cu ft -…

view full answer...

Answer 5

For your toy hauler patio door I recommend using some drop leg stabilizer jacks like the Stallion Stabilizer Jacks #288-01892-2. These jacks have a retracted height of 15-1/4" and extended height of 22-1/4" and a combined weight capacity of…

view full answer...

Answer 6

Great question! The All Terrain Landing Gear for RV Scissor Steps, #TLA8000, work with most factory scissor steps. Many steps like Brophy Scissor Steps #AS23 use rivets. You are correct - the rivets will need to be drilled out using a 1/4" drill…

view full answer...

Answer 7

The Brophy Camper Scissor Steps #AS24 that you referenced is designed to get removed when travelling. So the bracket would install on the camper under the door permanently and then you'd mount the steps to them when you are parked as needed. To…

view full answer...

Answer 8

I took a look at each of the scissor steps we carry and there are not any available that have the range of 18" to 26" you are looking for. You are not going to want to use the Brophy Camper Scissor Steps #AS23, which have a range of…

view full answer...

Answer 9

If you check out the install picture I attached for the #AS23 you can see where it normally installs at the rear of a camper that is installed on a truck. Without seeing your setup it's hard to be more specific but there should be a spot on the…

view full answer...

Answer 10

The Charge Wizard button on your Progressive Dynamics PD4560, replaced by the part #PD4560K18LS8, is only designed to be used for lead/acid batteries. This mode is supposed to be turned off when connected to lithium batteries so there is constant…

view full answer...