Valve Stem for 10x6 Inch Steel Trailer Wheel and 70 psi Tire

Question

Question:

What is the correct valve stem for the Americana Steel Trailer Wheel - 10inch x 6inch Rim - 5 on 4-1/2 - White? I will be mounting the Loadstar K399 Bias Trailer Tire - 205/65-10 - Load Range D. Tire pressure will be maximum 70 psi.

asked by: Joseph G

0

Expert Reply:

For American steel trailer wheel # AM20046 and a tire that requires 70 psi you will need valve stem # AM20904.

expert reply by: Michael H

0

Answer 1

The correct torque spec for a 10" steel trailer wheel like the Steel Solid Center Trailer Wheel part #AM20053 is between 75 and 85 ft. lbs.

view full answer...

Answer 2

Trailer tires should always be inflated to their maximum psi as listed on the sidewall of the tire itself. This means you should inflate the new tires on your trailer to the 80 psi that you mentioned in your question. The sticker on the trailer…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 10

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 11

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Valve Stem for 10x6 Inch Steel Trailer Wheel and 70 psi Tire

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching