Trailer Step Options for a Boat Trailer

Question

Question:

is there variety type of boat trailer steps? I saw many types of boat trailer steps now i only see one what is up?

asked by: Mike C

0

Expert Reply:

Currently the only other style of trailer step we offer aside from the # HE4036 that you referenced would be trailer fender steps like part # CE19011 for the left front/right rear or the part # CE19012 for the right front/left rear.

expert reply by: Jameson C

0

Answer 1

From my research I found that the width of a 16-ft Clackacraft weight forward drift boat is 83-inches wide and the height of the sides is 23-inches. To make sure you have enough strap to reach the trailer frame on each side of the boat I recommend a…

view full answer...

Answer 2

Yes we do, Johnny. Check out the CE Smith Tie-Down Bracket for Boat Trailers #CE26214G. This is a bolt-on bracket that will create a fixed-position tie-down on your trailer, is made of galvanized steel, and is 4" long x 1 15/16" wide.

view full answer...

Answer 3

I spoke with my contact at CE Smith and unfortunately they do not have a pull rating for the tie-down bracket #CE26214G. However, he did say that because the brackets are 7 gauge steel, 2 inches wide you should have no problems securely tying down a…

view full answer...

Answer 4

The best way to determine the height needed is to measure from the top of your trailer frame to the top of the sides of your boat. If the 40" Tall Guide-Ons #CE27626 sit right at or slightly above the sides of your boat then the shorter will…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Hey Melanie. The reason you can't find a replacement for your GE ARC15AACBL2 15,000 btu air conditioner is because they phased them out. In 2025 all RV AC systems had to change over to a new coolant called R32. This was a EPA mandated decision.…

view full answer...

Trailer Step Options for a Boat Trailer

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching