Expert Review Video:
Trailer Hitch Size:
2 Inch Hitch Opening
Towing Capacity:
1600 Pound Tongue Weight
16000 Pound Towing
Weight Distribution Towing Capacity:
1600 Pound Tongue Weight
16000 Pound Towing
Trailer Wiring:
2002 Ford F-350, 450, and 550 Cab and Chassis Trailer Wiring
Features:
This sturdy steel hitch from B&W is designed to fit your heavy-duty towing needs. Safety chain loops are built in and an electrical bracket is included for mounting your 7-way trailer connector (sold separately). Powder coat finish resists rust.
Installation Notes:
Drilling required for installation
Product fits vehicles with frame that is 34" wide outside to outside
Tech Tip:
Hitch is designed for cab and chassis models with a 5-1/2 inch drop.
More Information >Trailer Hitch Size:
2 Inch Hitch Opening
Towing Capacity:
1600 Pound Tongue Weight
16000 Pound Towing
Weight Distribution Towing Capacity:
1600 Pound Tongue Weight
16000 Pound Towing
Trailer Wiring:
2002 Ford F-350, 450, and 550 Cab and Chassis Trailer Wiring
Features:
This sturdy steel hitch from B&W is designed to fit your heavy-duty towing needs. Safety chain loops are built in and an electrical bracket is included for mounting your 7-way trailer connector (sold separately). Powder coat finish resists rust.
Installation Notes:
Drilling required for installation
Product fits vehicles with frame that is 34" wide outside to outside
Tech Tip:
Hitch is designed for cab and chassis models with an 8 inch drop.
More Information >Videos
for Trailer Hitch
Help Articles
for Trailer Hitch
Expert Answers
for Trailer Hitch
The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…
view full answer...A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…
view full answer...I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for…
view full answer...I&…
view full answer...Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846.…
view full answer...If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly -…
view full answer...Normal operating temperatures for drum brakes range from 150-400 degrees F. During certain stopping conditions the brake heat can exceed 600 degrees. The effectiveness and stopping power of the brakes is significantly reduced at these higher…
view full answer...If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…
view full answer...The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.
view full answer...The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the…
view full answer...A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…
view full answer...Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit…
view full answer...