Hi Gary; I'm sorry we don't have a video installing the #DX64XR at this time but I did go pull the installation manual out of the box for you. You need to remove the inner member and then route the cable as seen in the instructions. Dexter…
Hi Jonathan, that’s a great upgrade to look at, especially if you’re trying to smooth things out and take some of the harshness out of the ride. The MORryde CRE3000 part #MR27ZR could absolutely be a good fit for your 2019 Stryker 3513, but the key…
The tow package wiring is located under the dash above where your left knee would be as you were sitting at the wheel. Look for a wiring harness with a white tag on it. GM no longer has a connector, you'd just need to wire the controller directly…
Hi Nick! The B&W Anti-Rattle Clamp for 2" Hitch Receivers #BW45FR will work with any standard 2" tow & stow, including the Tow & Stow 3-Ball Mount - 2" Hitch - 5" Drop, 5-1/2" Rise - 10K - Black #BWTS10048B. That…
The Lockable Blower Rack for Utility Trailers #RA-19 is 39-1/2 inches tall and 13-1/2 inches wide. The 12 inch mesh sides will not support this rack, so you will need further bracing to your trailer like a rail to give you the stability needed to…
The 1" Long Black Torx Wall Liner Screw #WLS100 is the best option for the plywood installation. These screws are fine thread and made for metal studs. They have a tapping edge but often a starter or pilot hole should be drilled. You can then…
It all depends on how much room you have on the inside of your 5x10 trailer. The rail piece of the Pack'Em Trimmer Rack #PK-6-5 measures 46" while the upper mount is 11-3/4" tall from the hook to the piece that meets the rail. The…
I have attached 2 Images with the dimensions for the Pack'em Trimmer Rack for Enclosed Trailers #PK-6-5 as it would be too difficult to explain in text.
Hi Rob! The Bulldog Lifelong Trigger-Style Coupler Lock and 2" Trailer Hitch Receiver Lock - Chrome #BD580404 cannot have multiple set be keyed alike, unfortunately. If you are open to a different option though, the Trimax 2" Hitch Receiver…
The Buyers Products 50 Ton Air Compensated Pintle Hook part #337PH50 measures 2.38" deep by 3" wide. The inner eye diameter is 1.60" wide and 1.37" tall. I contacted Buyers and this hook uses a standard Lunette ring.
There is no recommended center to center distance for the Pack Em Trimmer Rack, #PK-6, but they must be mounted a minimum of 3ft apart. Trimmers come in different sizes and lengths, so it is best to mount the racks to fit your specific trimmers. The…
The Pack'Em Trimmer Rack #PK-6 that you referenced is not designed to be welded to a trailer. In the install notes Pack'Em makes it very clear that this should be bolted to a trailer with Grade 8 hardware. I spoke with my contact at Pack Em…
Hi Gary; I'm sorry we don't have a video installing the #DX64XR at this time but I did go pull the installation manual out of the box for you. You need to remove the inner member and then route the cable as seen in the instructions. Dexter…
Hi Jonathan, that’s a great upgrade to look at, especially if you’re trying to smooth things out and take some of the harshness out of the ride. The MORryde CRE3000 part #MR27ZR could absolutely be a good fit for your 2019 Stryker 3513, but the key…
The tow package wiring is located under the dash above where your left knee would be as you were sitting at the wheel. Look for a wiring harness with a white tag on it. GM no longer has a connector, you'd just need to wire the controller directly…
Hi Nick! The B&W Anti-Rattle Clamp for 2" Hitch Receivers #BW45FR will work with any standard 2" tow & stow, including the Tow & Stow 3-Ball Mount - 2" Hitch - 5" Drop, 5-1/2" Rise - 10K - Black #BWTS10048B. That…
The Lockable Blower Rack for Utility Trailers #RA-19 is 39-1/2 inches tall and 13-1/2 inches wide. The 12 inch mesh sides will not support this rack, so you will need further bracing to your trailer like a rail to give you the stability needed to…
The 1" Long Black Torx Wall Liner Screw #WLS100 is the best option for the plywood installation. These screws are fine thread and made for metal studs. They have a tapping edge but often a starter or pilot hole should be drilled. You can then…
It all depends on how much room you have on the inside of your 5x10 trailer. The rail piece of the Pack'Em Trimmer Rack #PK-6-5 measures 46" while the upper mount is 11-3/4" tall from the hook to the piece that meets the rail. The…
I have attached 2 Images with the dimensions for the Pack'em Trimmer Rack for Enclosed Trailers #PK-6-5 as it would be too difficult to explain in text.
Hi Rob! The Bulldog Lifelong Trigger-Style Coupler Lock and 2" Trailer Hitch Receiver Lock - Chrome #BD580404 cannot have multiple set be keyed alike, unfortunately. If you are open to a different option though, the Trimax 2" Hitch Receiver…
The Buyers Products 50 Ton Air Compensated Pintle Hook part #337PH50 measures 2.38" deep by 3" wide. The inner eye diameter is 1.60" wide and 1.37" tall. I contacted Buyers and this hook uses a standard Lunette ring.
There is no recommended center to center distance for the Pack Em Trimmer Rack, #PK-6, but they must be mounted a minimum of 3ft apart. Trimmers come in different sizes and lengths, so it is best to mount the racks to fit your specific trimmers. The…
The Pack'Em Trimmer Rack #PK-6 that you referenced is not designed to be welded to a trailer. In the install notes Pack'Em makes it very clear that this should be bolted to a trailer with Grade 8 hardware. I spoke with my contact at Pack Em…
I like the easy of navigation through the site. It only took me a couple of minutes to place my order. Thank You I will shop this sight again in the future.
Efficient and Durable Trimmer Racks for Your Trailer
Trimmer racks are essential for organizing and securing your trimmers and edgers on trailers. They save space, prevent damage, and make equipment easily accessible. Consider the type of trailer, installation ease, and capacity when choosing a rack. Ideal for lawn care professionals and enthusiasts looking to streamline their operations.
Trimmer racks are generally easy to install, often taking about 10 to 40 minutes. They come with clear instructions and require basic tools. Some users find they need to make minor adjustments, like cutting hooks for a flush fit in enclosed trailers. Overall, they are designed for straightforward installation on both open and enclosed trailers.
Yes, trimmer racks are versatile and can hold various trimmer sizes and types. They typically feature multiple notches or slots to securely store different equipment. Some racks may stick out slightly from the wall, but they provide ample room for easy access and storage of multiple trimmers or edgers.
Trimmer racks are built to withstand daily use and harsh conditions. They are sturdy and can handle the rigors of frequent loading and unloading. Some users suggest adding softer plastic to prevent wear on metal frames, but overall, these racks are designed to last and perform well even in tough environments.
Common issues include vague assembly instructions and the need for additional locks. These can be resolved by carefully reviewing the instructions and opting for a master lock set for better security. Proper installation orientation is crucial to avoid having to remove all trimmers to access one.
Yes, many trimmer racks offer expansion options, allowing you to add extensions for more equipment. They can be easily integrated into existing rack systems, making them a flexible choice for growing operations. Customization is possible with additional materials for specific trailer setups.
Filters
