Hey Alex. From the information I can find online it does look like your 2011 Keystone Cougar 318SAB does come prepped for a second AC unit. The bedroom roof vent should be reinforced and pre-wired for a 13.5k or 15k BTU unit. To check if your trailer…
Hey Phil! For a tandem axle trailer you will want two of the Leveling Kit with Wheel Chocks for Trailers and RVs #WS28ER. You are correct, one under each tire is best. I use these on my Jayco with one under each tire to keep them off the ground and…
The Replacement Controller and RF Remote for Lippert TV Lift System #LC253395 will not work on your existing RV T.V. lift due to the controller being specific to the motor. The motor, Lippert part 325978; has it's own pigtail that plugs into the…
Hello Herb, It's been a while, thanks for writing in. The short answer is no, the Micro-Air EasyTouch 353 is not currently compatible with the Furrion Chill Cube ducted system like the one included with #FR99TD. The Chill Cube is a newer,…
Welcome back Rich and thanks for the information! To replace your Sharp Carousel microwave R-820BK-F, I recommend the Greystone Built-In RV Convection Microwave item #GR27FR. It measures 21" wide x 11" tall x 15-3/4" deep.…
Hey Jonathan, RV air conditioners all fit a 14" x 14" hole so the only real important factors to determining the correct fit for you would be the BTU rating and whether you have a 6-pin or 9-pin connector. The 936000108 part number you…
Hey Mark, welcome back! Yes, that factory damper will be removed to install the Safe-T-Plus Steering Stabilizer #ST98MR. See the photos below. I also went ahead and linked the instructions and an installation video further down on this page for your…
Hey Skip, welcome back! The Vitrifrigo RV Refrigerator w/ Freezer item #VT56FR is going to need a 12v power supply. You can not plug it into a standard 110v outlet. You'll need to use the PowerMax AC to DC Converter item #PM54VR, which works with…
Hey Nang, the mounting holes on the back of the MORryde TV bracket part #MR85ZR can accommodate bolt sizes that are up to M8 in diameter. M8 is 8mm (about 0.315 inches) across its threads, while 1/4-20 is 0.25 inches. Typically TV hardware is M4, M5,…
In my experience the MORryde Wall Mount #MR82ZR will require additional mounting height to allow it to clear the storage door opening on most RV's. I have had better results using the Mount #MR38DR in the area you are looking to mount the TV.
Hey John, welcome back! I do have a way better functional solution for you. It's the Brandmotion Tailgate Delete Backup Camera with Wiring Harness item #BM67JR. This camera attaches to your license plate bracket. The other end will connect to the…
The Lippert Patio Upgrade Kit for Toy Hauler Garage Doors #LC27FR is a complete kit. It has all the hardware and struts that you need to convert your garage door into a patio. It may seem confusing because there were optional side rails that you…
WOW! I am impressed! I called to place my order and real person answered, spoke perfect English, albeit a slight southern accent, and my order was sent within a day, shipped quickly and I had it a few days later. I saved over a hundred dollars over local and installed it my self. I cant imagine how that they could do any better. THANKS!
Eric
Cedar Springs, MI
Lippert RV TV Mounts for vertical mounting
Designed for flat vertical surfaces, Lippert RV TV mounts fit cabinet or wall installs in RVs. Motorized lift options travel on a track and are not tested for horizontal mounting, so plan for vertical use only. Since every setup varies, confirm your mounting hole pattern and space, and be ready to make cabinet cutouts if you want the TV hidden when retracted.
Yes, a replacement is available only as a kit with the controller. Plan to replace both components together and follow pairing steps per the instructions. Confirm your current setup matches the kit to avoid compatibility issues.
No, Lippert RV TV lifts are designed for flat vertical mounting. Horizontal mounting hasn't been tested, so sideways installs behind a fireplace aren't recommended. Verify you have a solid vertical surface for the track and bracket. Custom orders for TV mounts aren't available.
No, detailed drawings or dimensions aren't provided. Measure the space where the track mounts and the TV will travel to ensure full movement. Identify any critical dimensions you need and verify clearance for the track, TV, and bracket before making cabinetry cuts.
The TV size can limit the stroke on these lifts. Confirm your cabinet height allows the lift to retract fully and extend to the viewing height you want. Check rack height and ensure nothing interferes with the screen or track path during movement.
Mount the track to a flat surface that can support the weight. The TV bracket slides up and down on the track, and you may need to cut holes if you want the TV hidden when retracted. Check the mounting hole pattern for your TV and verify clearances for full travel.
Filters
