Hey Alex. From the information I can find online it does look like your 2011 Keystone Cougar 318SAB does come prepped for a second AC unit. The bedroom roof vent should be reinforced and pre-wired for a 13.5k or 15k BTU unit. To check if your trailer…
Hey Phil! For a tandem axle trailer you will want two of the Leveling Kit with Wheel Chocks for Trailers and RVs #WS28ER. You are correct, one under each tire is best. I use these on my Jayco with one under each tire to keep them off the ground and…
The Replacement Controller and RF Remote for Lippert TV Lift System #LC253395 will not work on your existing RV T.V. lift due to the controller being specific to the motor. The motor, Lippert part 325978; has it's own pigtail that plugs into the…
Hello Herb, It's been a while, thanks for writing in. The short answer is no, the Micro-Air EasyTouch 353 is not currently compatible with the Furrion Chill Cube ducted system like the one included with #FR99TD. The Chill Cube is a newer,…
Welcome back Rich and thanks for the information! To replace your Sharp Carousel microwave R-820BK-F, I recommend the Greystone Built-In RV Convection Microwave item #GR27FR. It measures 21" wide x 11" tall x 15-3/4" deep.…
Hey Jonathan, RV air conditioners all fit a 14" x 14" hole so the only real important factors to determining the correct fit for you would be the BTU rating and whether you have a 6-pin or 9-pin connector. The 936000108 part number you…
Hey Mark, welcome back! Yes, that factory damper will be removed to install the Safe-T-Plus Steering Stabilizer #ST98MR. See the photos below. I also went ahead and linked the instructions and an installation video further down on this page for your…
Hey Skip, welcome back! The Vitrifrigo RV Refrigerator w/ Freezer item #VT56FR is going to need a 12v power supply. You can not plug it into a standard 110v outlet. You'll need to use the PowerMax AC to DC Converter item #PM54VR, which works with…
Hey Nang, the mounting holes on the back of the MORryde TV bracket part #MR85ZR can accommodate bolt sizes that are up to M8 in diameter. M8 is 8mm (about 0.315 inches) across its threads, while 1/4-20 is 0.25 inches. Typically TV hardware is M4, M5,…
In my experience the MORryde Wall Mount #MR82ZR will require additional mounting height to allow it to clear the storage door opening on most RV's. I have had better results using the Mount #MR38DR in the area you are looking to mount the TV.
Hey John, welcome back! I do have a way better functional solution for you. It's the Brandmotion Tailgate Delete Backup Camera with Wiring Harness item #BM67JR. This camera attaches to your license plate bracket. The other end will connect to the…
The Lippert Patio Upgrade Kit for Toy Hauler Garage Doors #LC27FR is a complete kit. It has all the hardware and struts that you need to convert your garage door into a patio. It may seem confusing because there were optional side rails that you…
Great on all counts. Selection, price, and prompt shipping. Could not ask for more.
Richard
Prairieville, LA
RV TV Mounts with 20 lbs capacity
Keep your lightweight screen secure on the road with a 20 lbs rv tv mount. Match your TV's weight and VESA pattern, and measure clearance near cabinets or doors so the set can move without interference. For a solid install in an RV wall, plan to hit studs or use a backing plate, and choose the swivel or drop-down motion that suits your viewing angles.
You can stop it partway down; the shocks hold at various heights without drifting. It locks in the upright position for travel. It also pivots side to side. Check door or walkway clearance in the partial-down spot you plan to use.
Lock the TV in the top position before hitting the road. Adding foam rubber blocks behind the TV can help silence rattling. Double-check fasteners after install. Inspect parts on arrival; if something is bent from shipping, straighten or replace before use to help prevent noise and movement.
Mount into studs or add a small backing board to hit solid structure. Center the base where the new drop-down motion needs it—don't assume the old bracket's offset will work. Expect a secure latch in the stowed position and that the TV may sit a bit farther out than a fixed mount. Swivel range can be limited, so confirm it fits your seating layout.
Yes, as long as your TV weighs 20 lbs or less and the VESA pattern matches the mount. Measure the space to be sure the drop-down and side-to-side pivot clear cabinets and doors. Some mounts in this range do not add vertical tilt at the TV plate, so check if horizontal pivot and drop-down cover your viewing angles.
Filters
