The Replacement Standard Dual Rack Repair Kit for Lippert RV In-Wall Slide-Outs - Fixed Side, #LC84FR is the left side of the slide-out as looking at it, facing it, from the outside. The float side, #LC26VR, will of course be the right side as facing…
Hi Ron, thanks for reaching out. I completely understand why you're checking that measurement before ordering since if the fins don't reach the slide wall, the seal won't do the job you're expecting. The Rubber Bulb Seal with Fins for…
Hey Stephen, we have the 16 foot etrailer awning part #e84QV that would work great on your car hauler. How tall is the side of the trailer? It shouldn't be a problem but the arms of this awning are 69 inches tall. We spent a lot of time on our…
Hey Jack congrats on the new Jeep! To flat tow a 2021 Jeep Wrangler Rubicon behind your 2012 Thor Hurricane 31J motorhome, I recommend the following parts: Tow Bar and Safety Chains - etrailer XHD Non-Binding Tow Bar for Roadmaster Direct-Connect…
Hello Andrew, good question. Basically the only difference between the composite kits and the standard (non-composite) kits is the application they are used for. Composite are used in motorhomes, the other are used on towable campers. It has to do…
Unfortunately, I cannot tell you what wiper seal you would need for your 2004 Keystone Outback. This is not something that is known just from the RV information. It depends on your particular slide-out. The best way to determine what wiper seal you…
Hey Jared, the pass through amp rating of the Rich Solar NOVA 3K12 3000W 12V Pure Sine Wave Inverter with Built-in Transfer Switch for RVs #RS79VR is 30 amps. What AC units do you have? This should be more than enough for that.
Hey, Skip! Happy to help get your new Jeep set up for flat towing. There is going to be a list of parts, so I'll go ahead and list them all below for ya. Blue Ox Base Plate: Part #BX1139 Blue Ox Avail Non-Binding Tow Bar: Part #BX7420 Demco…
To get right seal you'll need to remove a portion of the seal to get the side profile of your current seal. There are multiple types of applications for slide-out seals; Glue On, Peel-N-Stick, Press In, Push On, and Slide-On. There are multiple…
Hey Martin, The only difference I'm seeing between the Replacement Motor #TUS24FR and the Replacement Motor #LC125802 is that the TUS24FR has a 9000 RPM rating while the LC125802 has a 440 RPM rating while under load, which jumps up to 500 RPM…
You've got both a wiper seal and a bulb seal here with the wiper seals having a track for the bulb seal to slide onto. The Rubber Wiper Seal with Track for RV Slide Out #SR87FR you were already looking at is most likely the closest option to what…
The Fixed Dual Rack Repair Kit #LC84FR goes on the left side of the slide as you look at the slide out from the outside of the camper. So on the drivers side it will be the front of the slide. The Floating Dual Rack Repair Kit #LC26VR is going to be…
Very helpful/friendly Customer Service. Competitive Pricing. Shipping was Fast.
John
Mankato, MN
RV Slide Out Parts with Cylinder Replacements
Measure from the center of one port to the center of the other to match a cylinder; also note color like black or grey and verify extended and retracted lengths. Ends use 3/4"-10 nuts where threaded, and there is no seal kit, so replace when leaking. For creeping slides, perform the recommended hydraulic test to check for pressure loss, and add the o ring during install to avoid extra runs for parts.
Add an O-ring during installation to avoid a hardware store run. Recheck port-to-port center measurements before tightening everything down. Thread and fitting sizes should match your existing setup to prevent leaks.
Measure from the center of one port to the center of the other port to match the Cylinder. Note the color and compare extended and retracted lengths to your current unit. Fit can't be confirmed by year, make, and model alone, so remeasure to be sure before ordering.
A seal kit isn't offered for some Cylinders. Confirm whether a seal kit exists for your specific unit before teardown. If no kit is available, plan on replacing the Cylinder rather than attempting a reseal.
Start with a hydraulic Cylinder test to check for loss of pressure. You may find a crack in a valve in the manifold causing the issue; replace the defective part if a leak is found. Slide-out lock bars can help prevent creeping while towing as an added precaution.
Some Cylinder ends are threaded for a 3/4"-10 nut size. Verify that your Cylinder uses threaded ends and confirm the thread size on your unit. If in doubt, measure or check the specs stamped on the part before buying hardware.
Filters
