Hello Bruce, Thanks for writing in! Using butyl tape between the trailer body and the Single Axle Jeep Style Trailer Fender - Diamond Plate Aluminum - 13" to 15" #HP96VR is exactly the route I would go. It stays flexible, creates an…
Hey Craig. Had to go measure this myself out in our warehouse, I see we don't have this listed. That opening is large enough for a 1" thick panel. What are you looking to panel?
Hey Pam, welcome back! To replace your Pentair Shurflo Revolution 4008 Series By-Pass Pump, I recommend the Seaflo Diaphragm Pump for Boats and RVs item #SE57FR. This is a 12v powered three gallon per minute pump that is rated up to 55 psi. It works…
Hello Richard, Congratulations on the KZ Confluence 18RB! That is a really nice camper, and I like that KZ packed quite a bit into an 18-foot floorplan while still giving you a slide for some extra room inside. Yes, installing the etrailer RV…
Hi LaRue! The etrailer RV Slide-Out Topper #e67QV does include the awning rail track. This is everything you need for a complete slide-out topper installation. If you already have Solera mounting brackets installed from the factory, you will also…
Hey Brian! Yes, the Firestone Ride-Rite Air Helper Springs #F89VV will fit your 2025 Toyota Tundra. That is just the generic picture attached to that page, I can see how it would be confusing. These are designed to mount over the axle, and are…
Hi Mike, The JR Products Screen Door Slider part #37211185 has a depth of 1 1/4". That makes its overall dimensions 12 1/16" long x 11 7/8" wide x 1 1/4" deep. Though it isn't perfectly square at 12" x 12", it is…
Hey Kevin, yes we have the SumoSprings kit part #SS46KJ that is a fit for your 2025 Chevrolet Silverado 2500 HD. This is the medium density foam spring provides 2,800-lb support capacity at 50% compression and also requires no drilling for install!…
Hello Paul, There is one thing I like to have when I'm out enjoying the wilderness, and that's a toilet that feels like I'm at home. Well, I found just that for you. Since you're replacing the Dometic 300 in your 2021 Winnebago Minnie…
That is correct Trevor! The Progressive Dynamics 4500 Series RV Converter w/ Charge Wizard and AC/DC Distribution Panel item #PD4590K18LS8 would be the correct replacement. This is a 90-amp 2-in-1 AC/DC distribution panel and converter charger that…
Hey Arlen, welcome back! For a hitch I recommend the Curt Adjustable Width Trailer Hitch #13703. This Class III hitch fits 22" to 72" wide trailer frames and can be bolted or welded on for installation. It has a max tongue weight of 350 lbs…
Add a solid grab point with entry door handles that install easily and feel right. Ideal for RVs and enclosed trailers, they're a smart pick for replacements or new installs when you match measurements for a proper fit. Some options do not include mounting hardware, so double-check what's included before you start.
Yes, they've been used successfully on enclosed trailer side doors and as replacements on horse trailers. Check your door's mounting area and measurements to ensure a good match. If you're replacing a factory handle, compare dimensions to help it line up with existing holes.
Not all entry door handles include mounting hardware. Some come as the handle only. Check the product info to confirm. If hardware isn't included, source screws that suit your door material and frame. Be ready with sheet metal screws and a Phillips driver, and verify you have solid backing to mount into.
Match the handle's measurements to your original for an easy swap. Confirm overall length so it isn't too short, and check that your door frame has solid spots—like metal flanges or backing—to drill through. Lay out the holes and test-fit before tightening to keep the handle aligned and secure.
Verify the hole style if you need a 1/4inch square. Some grips use an 8 point star, Torx-like opening instead of square. Check close-up photos and specs before buying. If your latch or accessory requires a specific shape, match it exactly to avoid a mismatch during install.
Filters
