Bolt Hole Slot Size for Dutton Lainson Winch Handle DL70334

Question

Question:

What size is the bolt slot?

asked by: Steve

0

Expert Reply:

Hey Steve, the size of the slot in the Winch Replacement Handle, # DL70334, is 3/8 inches wide by 1/2 inches long. What winch do you have that you are looking for a replacement handle for?

expert reply by: Jameson C

0

Steve

5/29/2026

I have a Fulton winch. T2625.

Jameson C.

6/1/2026

@Steve Gotcha. Yeah it's unfortunate but Fulton is no longer around.

Answer 1

Thanks for reaching out, Ron. I was able to look into your axle using the information you provided, so that definitely helped identify the right ones. For your setup, the correct Timken bearings would be #TMK44FR and #TMK34FR. Those will match up…

view full answer...

Answer 2

Hi Tony; the #BK2-100 and #TMK52VR come with the same size bearings and grease seal. The main difference is the Timken name. This is usually associated with a higher quality bearings that are made in the USA which also accounts for the higher cost.

view full answer...

Answer 3

I went and pulled a Dutton Lainson Winch Handle part #DL70327 from our warehouse to measure the dimensions of the mounting hole and found it to be 1/2 inch by 3/4 inch.

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

Answer 12

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Bolt Hole Slot Size for Dutton Lainson Winch Handle DL70334

Product Page this Question was Asked From

Continue Researching