Gas Struts - Atlas Lift

Hi Susan, That part number comes up as a 60lb gas strut with a 20" extended length and 10mm socket so the Taylor Made Marine Gas Strut for Boat Hatches #3691843-60 would be a fit. To remove your current strut you'll need to stick a small…

Hey Peter, we have a hitch that fits your 2024 Hyundai Kona Electric with the Curt part #C43RV. The hitch you referenced does not fit the Electric models. What are you going to use the hitch for?

Hello Lydia, thanks for reaching out. Yes, there is suspension on the Yakima LowRider Kayak Trailer #Y82QD. It uses a leaf spring suspension system. You will see similar suspension on a lot of other trailers, it is quite common. A durable and…

Yes you can, there's no reason you couldn't back the Yakima Rack and Roll trailers like the part #Y08106 into water at a boat ramp.

There are many factors that go into selecting the correct gas shock, the easiest would be to simply match the new shock with the existing using any labels printed on the body. If none are present or you are adding a new one then you can use a formula…

Hey Lynn, I recommend using the MB Sturgis Sturgi-Stay T-Fitting w Hose #103615 which will allow you to connect your 20 lb tank to a 100 lb tank. The red type 1 ACME fitting will connect to one of your tanks, and the pigtail from the tank will…

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

The 5 sets of mounting holes on the Buyers Products Hitch Plate for Pintle Mounting - 1/2" x 15-1/2" - Ford #3371809030B measure center to center at 3-3/8" and vertically 1-3/4". The Gen-Y Adjustable 2-Ball Mount w/ 2"…

We do not recommend to modify the Surco Universal Exterior RV Ladder #SP502L to fit your camper as it may compromise the structural integrity of the ladder. However, if you choose too, you should be aware that the steps are welded to the frame of the…

While there isn't a life expectancy, per se, of the shocks on the Yakima Rack and Roll Trailer - 66" #Y08106 and 78" #Y08107, upgrading to the HD shocks is absolutely a good idea if your gear weighs around 200 llbs and certainly…

The 30205 bearing that you referenced has an inner diameter of just under 1 inch (0.985 to be exact). We do not have this particular bearing or a hub that uses this size bearing available. The #L44643 bearing that you also mentioned has an inner…

Yes, they can! The Yakima EasyRider Double Decker Trailer item #Y08129 has been designed to be submerged. The bearings are sealed so you won't have to worry about swapping them out. The Yakima Rack and Roll Trailer item #Y08107 didn't have…

Hi Susan, That part number comes up as a 60lb gas strut with a 20" extended length and 10mm socket so the Taylor Made Marine Gas Strut for Boat Hatches #3691843-60 would be a fit. To remove your current strut you'll need to stick a small…

Hey Peter, we have a hitch that fits your 2024 Hyundai Kona Electric with the Curt part #C43RV. The hitch you referenced does not fit the Electric models. What are you going to use the hitch for?

Hello Lydia, thanks for reaching out. Yes, there is suspension on the Yakima LowRider Kayak Trailer #Y82QD. It uses a leaf spring suspension system. You will see similar suspension on a lot of other trailers, it is quite common. A durable and…

Yes you can, there's no reason you couldn't back the Yakima Rack and Roll trailers like the part #Y08106 into water at a boat ramp.

There are many factors that go into selecting the correct gas shock, the easiest would be to simply match the new shock with the existing using any labels printed on the body. If none are present or you are adding a new one then you can use a formula…

Hey Lynn, I recommend using the MB Sturgis Sturgi-Stay T-Fitting w Hose #103615 which will allow you to connect your 20 lb tank to a 100 lb tank. The red type 1 ACME fitting will connect to one of your tanks, and the pigtail from the tank will…

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

The 5 sets of mounting holes on the Buyers Products Hitch Plate for Pintle Mounting - 1/2" x 15-1/2" - Ford #3371809030B measure center to center at 3-3/8" and vertically 1-3/4". The Gen-Y Adjustable 2-Ball Mount w/ 2"…

We do not recommend to modify the Surco Universal Exterior RV Ladder #SP502L to fit your camper as it may compromise the structural integrity of the ladder. However, if you choose too, you should be aware that the steps are welded to the frame of the…

While there isn't a life expectancy, per se, of the shocks on the Yakima Rack and Roll Trailer - 66" #Y08106 and 78" #Y08107, upgrading to the HD shocks is absolutely a good idea if your gear weighs around 200 llbs and certainly…

The 30205 bearing that you referenced has an inner diameter of just under 1 inch (0.985 to be exact). We do not have this particular bearing or a hub that uses this size bearing available. The #L44643 bearing that you also mentioned has an inner…

Yes, they can! The Yakima EasyRider Double Decker Trailer item #Y08129 has been designed to be submerged. The bearings are sealed so you won't have to worry about swapping them out. The Yakima Rack and Roll Trailer item #Y08107 didn't have…