The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…
A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…
According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…
You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…
Hey Justin, thanks for reaching out! I went out to the warehouse and confirmed that the Curt Adjustable 2-Ball Mount #C79NR measures 12-1/4" from the center of the hitch pin hole to the center of the hitch ball. Not sure what tape measure Curt…
Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a 1" shank…
In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.
Hey Dewain, we actually have a lock set specifically designed for use with the Bulletproof adjustable ball mount part #BPH77MR with the part #34061674-D. This comes with two locks for the platform of the ball mount and an additional lock for the…
The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…
...The maximum drop is 7-inches and maximum rise is 7-1/2 inches. They are adjusted in 1-inch increments.
I went to the warehouse to get the B&W Tow and Stow ball mount # BWTS10049B and provide you a couple...
Hey Sean, yes you can definitely use a stand alone system like a single-acting hydraulic pump to power a hydraulic trailer jack like the single action Stillwell lineup we just started carrying. For the Stillwell Atlas IV 10K Hydraulic Trailer Jack w/…
The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…
A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…
According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…
You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…
Hey Justin, thanks for reaching out! I went out to the warehouse and confirmed that the Curt Adjustable 2-Ball Mount #C79NR measures 12-1/4" from the center of the hitch pin hole to the center of the hitch ball. Not sure what tape measure Curt…
Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a 1" shank…
In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.
Hey Dewain, we actually have a lock set specifically designed for use with the Bulletproof adjustable ball mount part #BPH77MR with the part #34061674-D. This comes with two locks for the platform of the ball mount and an additional lock for the…
The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…
...The maximum drop is 7-inches and maximum rise is 7-1/2 inches. They are adjusted in 1-inch increments.
I went to the warehouse to get the B&W Tow and Stow ball mount # BWTS10049B and provide you a couple...
Hey Sean, yes you can definitely use a stand alone system like a single-acting hydraulic pump to power a hydraulic trailer jack like the single action Stillwell lineup we just started carrying. For the Stillwell Atlas IV 10K Hydraulic Trailer Jack w/…
I like the easy of navigation through the site. It only took me a couple of minutes to place my order. Thank You I will shop this sight again in the future.
Perfect Fit for Your 2-Inch Hitch with a 2-Inch Rise
Explore the robust and reliable trailer hitch ball mounts designed for 2-inch hitches with a 2-inch rise. Ideal for towing boats or trailers, these mounts offer sturdy construction and ease of use. Whether launching in saltwater or hauling across town, these mounts ensure a secure and stable connection.
A 2-inch rise helps level your trailer, ensuring a smoother and safer towing experience. This is especially useful when your vehicle's hitch is lower than the trailer's coupler, providing better control and reducing wear on your vehicle and trailer.
Look for ball mounts made from welded steel for durability and strength. A powder-coated finish can help resist rust, which is crucial if you're towing in saltwater environments. This combination ensures longevity and reliability under various conditions.
Many 2-inch hitch ball mounts come with a pin and clip, making installation straightforward. This feature is appreciated by those who want a ready-to-use solution without needing additional purchases, ensuring a secure fit right out of the box.
Some mounts may have minor paint imperfections, which can be a concern for rust, especially in saltwater use. It's advisable to inspect and touch up any nicks to maintain the mount's integrity and appearance over time.
A well-designed hitch ball slot ensures a tight fit, preventing loosening during towing. While some mounts lack a recessed slot, ensuring the ball is securely fastened is crucial for safety and performance, especially on long hauls.
Filters
