We offer 4 Class III hitches that are a confirmed fit for your 2015 Ford Edge Sport: • etrailer brand Class III hitch, part #e36RR • Curt Class III, part #C78KR • Curt Class III, part #C13234 • Draw-Tite Class III, part #75234 I'd eliminate the…
Hey Daniel, welcome back! You do not have to strip the wires before installing them on the TowSmart 4-Way Flat Connector Rapid Repair Trailer Wiring Kit item #TS68QR. The 4-way connectors have sharp metal prongs that slice the wiring insulation or…
The best I can do, without knowing your exact golf cart model, is show you how to calculate the maximum weight you can carry on your 2022 Ford F-250 when using the Mad-Ramps Pivoting Ramp System for ATV/UTV Ramps - 1,400-lbs - 2" Hitch, part…
There is a potential solution for you but the Arched Loading Ramp Set #288-07432-2 you referenced would not work with your 2017 GMC Sierra 2500HD with a 39-1/2 inch bed height. Instead, you may be able to use the Erickson Arched, Aluminum Loading…
To replace the OEM ramp for your 2002 Triton Elite, I recommend the Loading Ramp Set - Steel - 48" Long x 11" Wide x 1-1/2" Thick - 1,600 lbs - Qty 2 #288-07474-2 or the Aluminum Car Hauler Ramp Set - 48" x 14-1/2" - 6,000…
The MORryde Sliding Tray for RV Cargo Compartment #MR44FR has 1.57" of clearance before the tray starts. If you are needing more clearance than that the MORryde Sliding Tray Height Adjustment Kit #MR34VR will allow you to raise the tray…
I've attached the wiring diagram for you to check out, but it sounds like the compressor for your #AL57289 is not getting power. The wiring harness has an ignition wire which if not connected to an ignition source, will not wake up the compressor…
It won't be an issue. Since the combined weight of the #288-07452-2 is 1500 pounds, the ramps are designed to withstand the 1,450 pounds of your mower. However, if you are worried about it, you can always go with the #288-07474-2 which has a…
Hey Chris, the good news is yes, the Roadmaster Direct-Connect Base Plate Kit #RM-524431-5 that you have for your 2020 Ford F-150 Raptor will also work for your 2025 Ford F-150 Raptor. As of right now it does not look like we have an install kit for…
Yes, a trailer that is nose up can cause big problems. A level trailer is ideal and worth working toward for safety. The good news is that you can get the trailer almost exactly level with switching ball mounts. This is where an adjustable ball mount…
E-Track such as the Erickson Horizontal E-Track #E19148 can be used in any way that allows you to mount your pair of motorcycles. As you can see in some of the photos I've added, there is not a set way to add the track. You will need to take…
I have a solution for you, but the CargoSmart Arched Loading Ramps #3483070 are going to be about 7" tall at their tallest point when laid flat on the ground. If you don't mind folding up the ramps and storing them in the rear cargo area of…
A tri-fold ramp set packs small and opens wide for stable loading. Look for straps that secure the ramps to the bed with no kick out and locking devices that hold them while folded; note some side locks can rattle and some edges feel sharp. Use them in the intended direction only—sideways mounting isn't supported by tri-fold brackets—and choose enough length to avoid a steep approach.
Match the ramp capacity to your load and follow the use requirements to help prevent failures. Handle edges carefully; some stamped edges can feel sharp, so gloves help. Check the top lip where it meets the tailgate and keep an eye on hinge hardware—nuts can tighten and cause joints to jam. Tether chains so they don't tangle underfoot.
No—tri-fold ramp sets are not designed to be used sideways. The center and end brackets aren't rated to support weight in that direction. Align the ramp with the wheels you're loading. If you're loading a 3-wheel setup, place the ramps for the front wheels, then reposition for the single wheel as needed.
Secure the ramps to the bed with the provided straps or chains. With the straps tight, users noticed no kick out and solid, sturdy loading. Make sure the folded locks and side latches are clicked in place before setup; some latches can rattle loose when folded, so give them a quick check.
Longer ramps reduce the incline and make loading easier. Ramps between 70 and 80 inches were recommended to help with steep approaches, especially for snow blowers and similar equipment. If your setup feels too steep, step up in length to improve control and reduce the chance of bottoming out.
72 Inch Long
77 Inch Long
Filters
