Replacement PO1251925TB Grease Seal for Small Boat Trailer

Question

Question:

Looking for grease seals for my small boat trailer, make unknown. Old seal has # PO1251925TB. ID seems to be 1 1/4” X 1 15/16” OD. Thanks

asked by: Jim B

0

Expert Reply:

The closest grease seal we have available to the measurements you provided is the TruRyde Double Lip Grease Seal # RG06-010. This seal has an inner diameter of 1.249 inches and an outer diameter of 1.983 inches. You can use a digital caliper like # PTW80157 to verify these measurements on your current seal.

This will come with two grease seals. I have attached a short video review on this product just so you can get a better look at their dimensions.

expert reply by: Chris R

0

Answer 1

Appreciate that info and there are two hubs with inner and outer L44649 bearings, with the right one depending on your wheel bolt pattern (as we don't have any way of knowing specifically what hub is on an '87 Tracker trailer). Both are for…

view full answer...

Answer 2

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 3

Yes, it will. The Roadmaster Battery Disconnect with Switch for Towed Vehicle w/ Flat Tow Brake System item #RM-766 is not only compatible with your 2024 Buick Encore GX but it is recommended to be used by Roadmaster. This a great part that makes…

view full answer...

Answer 4

To determine what the correct replacement hubs are for your Magic Tilt trailer there is a little bit of information that we will need. We will need to find out inner diameter of both the Inner and Outer Bearings as well as the inner diameter of the…

view full answer...

Answer 5

The Kodiak Disc Brake Kit - 10" Hub/Rotor - 5 on 4-1/2 - Dacromet- 3,500 lbs #K2HR35D may fit your UFP DB-42 axle. I don't have the specs on that axle to confirm, however if your spindle has an inner bearing diameter of 1.378 inches and…

view full answer...

Answer 6

This question actually comes up quite a bit. The hitch receiver tube and safety chain plate will block the sensors located under the rear bumper in the center. However, the sensors further to the right or left will still function and allow you to…

view full answer...

Answer 7

The BTR and BT8 denotations refer to the spindle, not the trailer hub. The difference between a BTR and BT8 spindle is that the BTR spindle uses a 1.063" diameter L44649 bearing and the BT8 spindle uses a 0.99" diameter L44643 bearing. In…

view full answer...

Answer 8

Based on my research Dexter seal 63052 appears to have been used in a military trailer application. I also could not find a current production seal that cross-references with this one. In this case the way to find a new seal is to measure the hub…

view full answer...

Answer 9

Hi Brian; grease seals with a 2.125" inner diameter and 2.250" ID are both found on 5,200 lb axles. I reached out to Dexter and they confirmed that the 10-36 grease seal with a 2.250" ID is correct for the 184357 axle. The #RG06-070 is…

view full answer...

Answer 10

You will want to measure your spindle to make sure (see accompanying photo) but the double lip grease seal that fits Dexter axles that are rated for 5,200 lbs - 7,000 lbs is #GS-2125DL. If you look at the photo you will want to use a digital caliper…

view full answer...

Replacement PO1251925TB Grease Seal for Small Boat Trailer

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching