# 1
Draw-Tite Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/2" Long - 7.5K
GOOD QUALITY
# 2
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K
this hitch is great. i needed a longer ball mount to give me more room between my trailer jack and spare tire on the tail gate of my jeep wrangler. it is very hard to find a extra long ball mount. i found etrailer has them and a lot of other fine products.
# 3
Hidden Hitch Ball Mount - 3/4" Rise, 2" Drop - 15-3/4" Long - 6,000 lbs
This was a gift, the recipient was very excited to receive it, she will now be able to tow the ski boat behind her jeep, she couldn't before due to the spare tire interfering with her previous hitch.
Just what I needed to add clearance for towing our 1962 Shasta Astroflyte that has a bunk that hangs out over the tongue.
# 4
Ball Mount 3/4" Rise or 2" Drop - 12-5/8" Long
The D-26 is just the right length for my 2008 Jeep Wrangler. The 32in spare tire doesn't get in the way of the hitch even with 3/4" rise. yay
Love it. It's on jeep wrangler and now I can hook up my trailer and crank up the tongue stand without hitting my spare tire cover
# 5
Convert-A-Ball Ball Mount for 2" Hitches - 10-3/4" Rise, 12" Drop - 7,000 lbs
Perfect Fit! 07-12 Jeep Wrangler JK with 3.5" lift. This was the exact product to get the trailer back on level. Great service and fast shipping.
# 6
Curt Multipurpose Ball Mount with 2" Receiver for Bike Racks and Cargo Carriers - 7,500 lbs
Excellent product - very strong and secure! Does not, however, fit my 2016 Jeep Wrangler Unlimited. It is about 3.5 inches too short to clear the spare, and about that much too tall to go under the spare.
Hitch was as expected... appreciate the extra communication by etrailer.
# 7
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
Longer stinger let me drop the tailgate on my Tacoma with trailer attached. Replaced a similar but shorter Curt hitch and both are very substantial and well made for the weight of my trailer.
With good information from the website it was easy to order a Curt 2" Trailer Hitch, the Upgraded Circuit Protected Tail Light Converter Hardwire Kit w/ 4-Pole Connector and Circuit Tester - 119178KIT, Curt Ball Mount for 2" Hitches (3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs - D-4), Curt Pin and Clip Hitch Receiver - C21500, Rubber Tube Cover for 2" Trailer Hitch Receivers - I-728,Review, and 2" hitch ball 40038. Parts were delivered earlier than the initial estimate. Self installation (on a sloped drive way) took just under 2 hour. The fit of parts was very good, instructions and on-line video's were very helpful. My Kia did not have the wire plug in option, but the splice connections in the wire kit were easy to install. Most of the parts are hidden from view when the ball mount is not used.
# 8
Curt Ball Mount for 2" Hitches - 4" Rise, 6" Drop - 14-1/4" Long - 6,000 lbs
i HAVE PURCHASED SEVERAL PRODUCTS FROM ETRAILER. HAVE ALWAYS HAD QUICK DELIVERY OF THE PRODUCT I ORDERED. PRODUCTS WORK WELL AND ARE EXCELLENT QUALITY. SERVICE, INFORMATION AND ASSISTANCE FROM ETRAILER IS TOP NOTCH, THAT IS WHY i HAVE BEEN A REPEAT CUSTOMER FOR A LONG TIME.
Very well made ball mount. Etrailer is a great company to do business with, huge inventory and shipping second to none. Buy American! Ron
# 9
Convert-A-Ball Ball Mount for 2" Hitches - 8-3/4" Rise - 10" Drop - 8,000 lbs
This is such a great idea! It works flawlessly with my Jeep Wrangler and my Offroad trailer. The dampening incorporated into the hitch makes my ride so much smoother. I used to hear the clanking, tapping and banging while braking and while trailering offroad, but not any more! I highly recommend this hitch to anyone.
This particular 10" drop hitch ball mount was the right mixture of quality, features, and low price. It appears to be quality built, and the shock cushioning is an unexpected plus. I used it right away today when I received it to tow my utility trailer to Lowe's. The trailer made less noise and rattling around in the receiver with this product. I have a lifted Jeep Wrangler and the 10" drop leveled out the trailer pretty well. Also happy the AMSC10 is made in the U.S.A. ! Ordering process and follow-up by e-trailer were first rate. Appreciate the additional quick delivery.
# 10
Lock N Roll Articulating Trailer Hitch for 2" Receivers - Vehicle Side - 11,000 lbs
It will fit on A 2022 Jeep Wrangler And not interfere Would the spare tire or tailgate in the up orientation. I needed to Level out my Taxa Woollybear.
Both connecting lock n roll products are a great addition to my project roof top tent, utility, kayak mounted, Solar energy equipped overland adventure trailer. Not only has my travel range increased due to this go anywhere upgrade, but my trailer security and its value has increased also. I am a very happy customer. So.e fab work may be necessary.
# 11
Brophy Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 13-1/4" Long - 10K
I had never towed anything before and recently bought a small pop up camper. The Ball mount was to short for my 2011 Jeep Wrangler and I had to remove the spare tire each time to correctly hitch. This Ball mount is the perfect solution. Just the correct length to hitch up with out any more problems. Also better made and less expensive then the dealer sold me. By reading the questions asked by customers I was able to pick out the correct product. Great Web Site and Excellent service.
I needed the extended hitch for a Jeep Wrangler Unlimited. With a standard length hitch when not on level ground I could not hook up or disconnect my utility trailer because the flip up coupler lock would hit the bottom of the rear-mounted spare. This extended hitch takes care of that by bringing the ball away from the tire allowing a flip up coupler lock to be completely vertical and disengaged
# 12
Curt Ball Mount for 2" Hitches - 8" Rise, 9-1/4" Drop - 14" Long - 5K
I've made several purchases from e-trailer.com and have had excellent service and quick delivery. The front hitch was difficult to mount because the straps welded to the 1/2 inch nut weren't quite long enough to catch the thru bolt. I had a fairly hard time lining the nut up but was able to do it.
The D-26 is just the right length for my 2008 Jeep Wrangler. The 32in spare tire doesn't get in the way of the hitch even with 3/4" rise. yay
# 13
Curt Ball Mount w/ Sway Control Tab for 2" Hitches - 3/4" Rise, 2" Drop - 7,500 lbs
I cannot use this ball mount because the shaft is too short that goes into hitch receiver on my one ton Dodge truck. It does not allow enough room between truck back bumper and ball to allow any trailer tongue to be put on ball.
Purchased this hitch as a companion for our Reese anti sway control. The small ball for the Reese sway control fits in the bracket and the 2” drop on the hitch is exactly what we needed to have our Jayco camper level when towing.
# 14
Drawbar for 1-1/4" Hitch - 2-5/8" Rise, 3-1/4" Drop - 7-3/16" Long - 3.5K
The hitch works great. The service was excellent!!! I'm going back and having a hitch put on my other car soon. Thank you.
Everything was perfect.! Nice paint, package, and fast shipping.! Im satisfied.!
# 15
Convert-A-Ball Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10,000 lbs
This device is a great idea. I would highly recommend it for towing with smaller uni-body utility vehicles and small trucks because of their smaller drive components, but any vehicle will benefit. This is really nice with utility trailers that tend to bounce over potholes. I've used this product with a Jeep Wrangler and CJ7, Toyota RAV 4, Sienna and 4Runner as well as a Chevy Suburban.
This is such a great idea! It works flawlessly with my Jeep Wrangler and my Offroad trailer. The dampening incorporated into the hitch makes my ride so much smoother. I used to hear the clanking, tapping and banging while braking and while trailering offroad, but not any more! I highly recommend this hitch to anyone.
# 16
Brophy Drawbar for 1-1/4" Hitches - 5-1/2" Rise, 6" Drop - 7-1/4" Long - 3.5K
Works fine. Hole for the ball was not drilled properly and I had to ream out the hole slightly so the shaft on the ball would fit properly.
I just purchased a new hideaway hitch system. But the hitch sits only 15 inches off the ground at best. And, my trailer coupling is 22-23 inches off ground. So l needed 7-8 inches of rise on the new 1.25 inch receiver system. Internet research took me to etrailer and the Brophy hitch. I got 5.5 inches with the Brophy hitch, the highest available for a 1.25 inch receiver I could find. The others are limited to 5 inches max. I added another 1.5 inches with your Curt shock absorbing hitch. Voila, with a combined 7 inches of rise and on level ground the trailer now rides perfectly level!!!! Both parts were very easy to connect. Delivery was speedy. Thank you for saving the day and my investment in an expensive new hideaway hitch!
# 17
Convert-A-Ball Ball Mount for 2" Hitches - 6-3/4" Rise, 8" Drop - 10,000 lbs
Excellent quality. Ordering was easy and delivery was fast. Looks like the perfect amount of drop for my jeep to keep trailers level.
This is such a great idea! It works flawlessly with my Jeep Wrangler and my Offroad trailer. The dampening incorporated into the hitch makes my ride so much smoother. I used to hear the clanking, tapping and banging while braking and while trailering offroad, but not any more! I highly recommend this hitch to anyone.
What our customers are saying:
"very easy to shop"