# 1
Electric Jack w/ Footplate - A-Frame - 25-1/8" Lift - 3.5K - Black
Great product and Trailer has great customer service. It's to bad that the shipping companies do not take better care with the items during shipping! will receive replacement parts to fix what was broken, but it causes lots of extra work for the customer. will have to take complete jack off to replace the broken motor cover because of shipping carelessness!! regards, Dan Ewert
This little rig has teeth! Much faster than i expected. About a 30 minute installation from old lift removal to new and wiring. Super simple. Great addition to my hangar 18!
# 2
Stabilizer Jack - 6-1/4" Drop Leg Travel - 18" - 650 lbs - Qty 1
Gave it a three due to the modifications that had to be done to make it fit. I had to grind down the outside of the pad about 3/16" to make the stabilizer fit up into the bumper of our Scamp. In addition, I shimmed the top down about 5/32 so it would lock into place without forcing it. One stabilizer had epoxy which looks very sloppy. This on the edge where it should be spot welded - hope this is the case! Fortunately, I'd read reviews indicating that this was not a direct replacement for Scamp 13'ers. Folks should be aware they may have to do some work since the stabilizers may not fit out of the box. Once modified, they work as expected.
I drilled two 3/8" holes in the top of the rail and used two stainless bolts to hold it on. Works very well for this application. It folds and holds the trailer for loading, and if I have to leave it somewhere, and don't want the tongue sitting on the ground. I used it on a Harbor Freight 4x4 trailer I am building to pull with my Can-Am Spyder. Love it!!!
# 3
Stromberg Carlson Electric Trailer Jack - Drop Leg - A-Frame - 24" Lift - 3,500 lbs - White
Jack works very well. Not fast but gets the job done. Unfortunately I can't lower my tailgate fully without hitting the jack. Tried to rotate the head as I saw some jacks allowed. This one won't allow that. Very satisfied otherwise. Used less than one full season so can't offer an opinion on durability.
Mounted quick and easy. Plenty of wire for electrical hook up. Lots of power even with a full load of water in the front tank. The only change I made to installation was longer bolts to accept washers and nuts to the bottom side of hitch. I didn't trust the taped holes in the thin hitch frame. This was no fault of the new jack. Still working strong. A back saver that's worth the money. I should have bought one years ago!
# 4
Scissor Stabilizer Jack - 18-3/4" Travel - 2,500 lbs - Qty 1
Jacks Appear to be exactly as advertised. Delivery was early. I bought this pair of jacks to replace a J-2500 that came on my Kodiak Cub. The J-2500 bent when I over torqued it while jack was not extended far enough. I found out this 5000 pound model is not a drop in replacement. I had to drill additional mounting hole in the jack to match existing holes in trailer frame.
They went on a custom made trailer build that’s not yet in service. Seem to function as advertised.
# 5
Stromberg Carlson Electric A-Frame Tongue Jack - 18" Lift - 2,500 lbs
It installed very easy. For a 2500lbs jack, it seems a little light weight. It does lift the trailer but seems kinda wobbly because the post size is so small. Other than that it works as advertised. Thank you for getting it to me so fast.
This is the second one of these we've owned. Works real good, a bit of over kill. The thing could probably lift the whole trailer.
# 6
Fulton Drop-Leg Stabilizer Jack with Mounting Channel - Weld-On - 28" Leg - 13" Bracket -
Beautifully made and a solid drop leg. Do I need to say more? You get what you pay for.
Product was exactly what I was looking for. Only issue is the one square latch pin is missing.
# 7
Leveling Scissor Jack - 24" Lift - 5,000 lbs
Much better jack than the one that came with the tow trailer. This 70 year old woman had no difficulties installing it. One year later still works great!
leveling jack was delivered very promptly and in good shape. installed on my 5th wheel easily and works fine. a bit lighter duty than the OEM jack but darn good value for the price and will get the job done. etrailer is the best!
# 8
Stabilizer Jacks - 6-1/4" Drop Leg Travel - 18" - 650 lbs - Qty 2
Easy to install both in under an hour. Provide good stability to small (boat) trailer when deployed. I can see the paint/powder will be as durable as they were as simple to install
Bought these for my cargo trailer. Did not get around to installing them for several months. When I finally unpacked them, the “foot” of one came off while I was unwrapping them. I had to drill holes and add a few screws to reattach. There was no damage to the box. They still serve their purpose, just disappointing.
# 9
Lippert Power Stance Electric Trailer Jack w/ 7-Way Plug - A-Frame - 18" Lift - 3,500 lbs
I was amazed at how quickly my replacement from etrailer arrived. I was a bit worried that the installation of my new jack would be more difficult that I expected. The reverse proved to be the case, it was very simple to place the trailer tongue on jack stands, remove the old jack and install the new one. As the old saying goes "even a cave man could do it."
Awesome product. My back thanks you. Very easy to install. Only thing I would change is the speed of the motor. A bit slow but still better than hand cranking.
# 10
Lippert High-Speed Power Stabilizer Jack - Black Waterproof Switch Kit - 30" Lift
Box is damaged and tape all over with clear tape holding box closed and first thought is missing parts and paper work and instructions to install ! Pictures taken and open up box finding all parts inside except for the paper work instructions to install, also the rubber cover for the water poof motor is damaged also!
I purchased a lipoert electric stabilizer jack from trailer and it was a perfect fit and it worked awesome I want to thank Karen and all the other ones that made this experience possible and I personally would recommend using eteailer for all of the parts that are needed for a travel trail thank you so very much. Rob Sams.
# 11
Lippert High-Speed Power Stabilizer Jack - White Switch Kit - 30" Lift
Pros: Works better than I anticipated. Looks great and has better ground clearance than the stock scissor-jack stabilizers. Cons: Installation instructions/documentation weak or non-existent. If all of the instructions, wiring diagrams and documentation were in one place on the web page under a separate tab rather than having to dig through the reviews and the Q & A’s, I would have given this a 5 star rating. I ordered the LCI Power Stabilizer Jacks with the white switch Kit (LC369774) because I wanted the switches mounted in the camper wall so they would be better protected than if they were mounted in the flimsy fender skirts of my camper. I also needed the bolt-on spacer kit (LC673594) for both the front and rear jacks to clear a propane line that runs along the length of the frame. Installation was relatively easy, although there are NO instructions on how to install the spacers kits; the video on etrailer.com was no help whatsoever with the installation. I bolted the jack mount brackets to the shorter side of the spacers using carriage bolts and flange nuts; the slotted holes in the spacers accepted the carriage bolts, aligned perfectly with the holes in the jack mounts, and allowed me to install them without having to try to fit a wrench inside. Then it was just a matter of drilling holes in the frame at the appropriate spacing for flange bolts/nuts through the slotted holes on the end of spacers. I was very pleased with how the switches and the switch compartments looked once installed. Again, though, it took lots of digging to find the wiring diagram and then the matrix for the switch wire colors, because the wires on the white switch are colored differently than the black switch that all of the diagrams show. Also, it states on the jack installation instruction sheet that the power must be a minimum of 10 gauge wire (AWG-10), but nowhere on the wiring diagram does it say anything about that. AWG-10 is a MUST because of the way current drops over a distance. In the case of my camper, it is a 30 foot run which requires that gauge of wire for 20 AMPs.
This stabilizer works very well. I replaced the original Lippert unit on my 2008 5th wheel as the parts I needed were no longer available. The original Lippert unit worked great until some idiot in a drunken stupor decided to move it with the stabilizer in the “down” position. I probably won’t do that again anytime soon. DOH!!!
# 12
Lippert Electric Trailer Jack with Footplate - A-Frame - 18" Lift - 3,500 lbs - Black
The bolt pattern matched my trailer so it was very easy. No skill needed. I soldered a connection on and hooked it directly into the battery. I had to drill a hole for my foot extension. So far so good. 23 foot travel trailer.
As always a big help in getting what I need, and wanted. Good tec help, fast service. Already installed.
# 13
Electric Trailer Jack - Drop Leg - A-Frame - 22-1/2" Lift - 3,500 lbs
This jack was the perfect solution for my application. I have a new enclosed trailer that came with a manual crank and only a tiny battery to run the lights. I did not want the expense of having to buy and cable up a larger battery to just support the tongue jack. Took me 5 minutes to install this new jack using the three bolts that were already on my OEM jack. Now I just back up my truck, plug in the 7-way, and I'm able to move the tongue up and down as needed. Great!
I love my new electric trailer jack ! It has a 7 pin RV plug which makes it so convenient to power. There are lights on both sides to shine onto the hitch after dark. There is a bubble level on top to know when the camper is at least level enough to start setting up. It all works great !
# 14
Ultra-Fab Power Twin II Electric Stabilizer with Dual Motors - 30" Lift - 6,000 lbs
Finally got around to installing my PT II Stabilizers 30" front and rear of our 26' Surveyor. Pre - assembled them to make sure they went together ok. Luckily I had two sources for power front & rear which made wiring easy, I used a Buss block to make all positive connections, grounds straight to frame, soldered all connections and heat srinked to seal. Using the 3/8" self tappers was fun.Well got it all together and all works well makes trailer very stable, don't have to worry about scissor jacks collapsing anymore.
I finished the assembly and install of the power twin II stabilizer and have included pictures of the install. This is a good quality unit and I am very happy with how it works. Bob
# 15
Stromberg Carlson Electric Trailer Jack - Drop Leg - A-Frame - 23" Lift - 5,000 lbs - Black
I was extremely impressed with the recent technical and customer support from etrailer. Over the weekend, they answered my questions to select the appropriate replacement electric jack for my Airstream. Also, when there was a shipping delay (not etrailer’s fault), Rose provided prompt responses and professional support. I will continue to use etrailer for my RV needs.
Works flawlessly. Maybe the only thing I could complain about is it is slower than I think it could be. Along with the side lights could always be brighter. Works great, install kit is awesome, and it works without a stutter.
# 16
Phoenix Electric Trailer Jack with Remote - A-Frame - 26" Lift - 5,500 lbs
This is awesome and so easy to install. Took longer to open the box then to set it up. We had ordered something similar to this for our old camper. It took us hours to get it to fit right. This was extremely easy to install. My husband loves the memory feature on this thing.
My order arrived damaged. etrailer was immediate to remedy. The same day a return for pickup at my home and a new item was shipped out. I plan on installing the jack tomorrow.
# 17
MORryde Scissor Jack Cross Brace Stabilizer for Trailers and RVs
just installed on rear of the camper for now it made such a stabilized difference. i might be installing in the front next . had to drill larger holes in my jack but it was not hard. about 1 hour installation
Shipping was not so great on the boxes. Looks like they fell out of a moving truck. Really the problem is that the metal arm tips that pop out of the box in shipping. Are scraped and will need to be painted so they don’t rust out.
# 18
Electric Jack w/ Footplate and 7-Way Plug - A-Frame - 25-1/8" Lift - 3.5K - Black
The 7-way plug electric jack is a great replacement for my crank handle jack. I did not want to install and maintain a 12V battery for just a jack so this is an easy plug and play solution for me.
7 pin easy hook up for trailer jack does not work on my 2020 ford ranger. Missing 12v power to jack control? any advice in Trouble shooting. Is there a compatibilty problem with ranger to your jack 7 pin config? Will use manual hook to battery rather then ask for replacement jack if possible?. Before I cut any wires and void warranty. Is all I have to do is cut and splice the fused red wire to a positive battery terminal to do this. What abount grounding? Please advise should I modify and wire direct or return jack back for refund/replace
# 19
Bulldog Powered Drive Trailer Jack - Drop Leg - A-Frame - 22" Lift - 4,000 lbs - Black
Overall the product does exactly what it's intended for and works well. I however assumed that this would be a simple R&R for my camper and did very little installation research other that the video provided on etrailer' s website Sadly it did not fit. Not at all. I didn't take into account that have a double framed hitch toyhauler. The baseplate on the factory leg was a TRIANGLE.....this unit was ROUND. Also the primary shaft was thicker than stock and would not drop down into place I know modifying is frowned upon, but I found that ALL powered hitch legs I found have round mounting plates and it's not mentioned the leg tube is thicker than OEM? Since NOT having a power lift wasn't an option for this camper application...too heavy in the front when ATVS loaded to lift for setting the equalizer hitch tension bars, I proceeded to modify by cutting the rear rounded mounting base ... square. Took off about 1/2 inch. Then I took my metal Dremel sanding bit and increased the hitch leg hole diameter slightly. Took about 1 hr. Dropped it in. Wired it. Tested it. All good. If you can't post this I understand, but take note that some of your website descriptions may need to be enhanced. Thanks!
This has been a great trailer jack a year into installing it on my 12 x 6 enclosed cargo/camping trailer. The jack is out in the elements 24/7, gets used almost every weekend and is still going strong. I would definitely purchase this product again for my next trailer.
What our customers are saying:
"very easy to shop"