Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
This V-shaped identification bar uses three premium red LEDs that deliver bright, clear light with minimal power draw. The LEDs are rated for up to 100,000 hours of operation and run efficiently on 9V–14V DC, drawing only 0.07–0.09 amps. You’ll get strong visibility while keeping electrical load low—perfect for a setup that you can trust trip after trip.
When your trailer measures 80" or wider, proper rear identification lighting isn’t just helpful—it’s required for safety compliance. This light meets or exceeds FMVSS 108 standards and clearly marks wide trailers so other drivers can see you in low light or from a distance. The V-shape design fits neatly along a rear V-bend cross member, giving you a clean, professional look that also improves safety awareness on the road.
Water exposure is no problem here. The housing is sealed to an IP68 rating, and the TecSeal urethane potting protects the military-grade circuit board far better than standard epoxy. Whether you’re backing into the water or driving through rain, this light resists moisture and corrosion while keeping the electronics completely protected.
The clear UV-resistant lens is built to handle vibration and impact without cracking or fading. Its rugged build keeps the LEDs protected so the light stays bright even after years of use. This durability makes it a dependable upgrade for anyone who wants strong, consistent lighting without dealing with bulb failures or fragile housings.
You can mount this 12-15/16" long by 2" wide by 1/2" thick identification bar directly to your trailer surface—no complicated brackets or bulky housing needed. With 9" between mounting holes and a 58" wire lead, it’s easy to position and connect exactly where you need it for clear rear visibility every time you’re on the move.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hello everybody. This is Jeff at etrailer.com. Today, we're gonna take a look at this V-shaped clear ID light bar for over 80 inch wide boat trailers. Now, this is a V-shape ID light, which will function as a rear identification light bar on boat trailers that are wider than 80 inches. And it is required by law to have a rear identification light when the trailer is wider than 80 inches. This is a nice low profile design, so it allows for installation in tight spaces.
And they do use sealed waterproof housing and lens unit, which is submersible. It does have an IP 68 rating and that means it's resistant to submersion up to maximum depth of five feet underwater for up to about 30 minutes. Now, they do use military-grade construction of the circuit board on this light. Uses a urethane potting, which offers better protection than the common epoxy potting. And the LEDs they use on these lights are premium LEDs.
They are energy efficient, long-lasting, vibration resistant. They are rated for up to 100,000 hours of operation. Now, at the end of this video, I am gonna hook this light up to some 12 volt power to show you how bright it is. It is a durable polycarbonate housing and lens. Now, this is a clear lens but it is over three red LEDs.
It is compatible with 12 volt DC systems, and it is a surface mount installation. Now, the hardware to install it is not included. There's two holes here that the hardware would go through to hold it into place. It does hardwire to your trailer. It's a two-wire design, a power and a ground wire, and they give you a wire length of about 58 inches.
Now, this light does meet or exceed the Federal Motor Vehicle Safety Standard 108 standards. Few specs on it, the input voltage is nine volts to 14 volts. Power draw is .07 to .09 amps. So, what I wanna do now is give you some measurements and then we'll hook it up to some power. The length from this end to this end, put a ruler on it. Now, this is a 13 inch length ruler, so it's just under 13. It's right at 12 15/16 of an inch. The height when this is installed is gonna be right at two inches tall. And the thickness of this light is only gonna be right at about a half an inch thick. Now, the distance between those two mounting holes we mentioned, if you go center to center is right at nine inches. So, what we're gonna do now is we'll go ahead and hook up our ground wire, and we'll hook up our power wire. And then with those hooked up, I'll go ahead and turn on the 12 volt power, and there you can see the lights light up. I'll go ahead and turn off the overhead lights, and there you can see the clear lens with the red LEDs. And what I'm gonna do is actually then zoom back out, and you can see it at a wider distance how bright those lights are. Turn back on our overhead lights. Go ahead and turn off our power. But that should do it for the review on this V-shaped clear ID light bar for over 80 inch wide boat trailers..
Ratings & Reviews
Bob
10/1/2023
Im pleased to report that it is still doing its job after a year in service.
Mike L.
9/13/2025
I'm sorry that happened! The product does carry a limited lifetime warranty so I'll have one of our Customer Service folks reach out to you.
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Jon
8/20/2026
Part still looks and works great.