In-stock alternatives that are ready to ship
Double-eye leaf spring acts as part of a trailer's suspension system by providing an attachment point for a 6,000-lb axle. Spring flexes to resist shock and also ensures a smooth ride. Includes bushings with 9/16" inner diameter.
Features:
Specs:
| Part Number | A | B | C | D |
|---|---|---|---|---|
| 072-073-00 | 13" | - | 25-3/8" | 2-13/16" |
Note: To ensure proper axle alignment and suspension performance, leaf springs should always be replaced in pairs.
Leaf springs are an integral part of your trailer suspension system. The leaf springs provide the attachment points for your trailer's axle, suspending it from the frame of your trailer. Each spring flexes to absorb road shock as you travel, allowing the axle to move somewhat independently of the rest of your trailer. This helps to reduce wear and tear on the trailer and also ensures a smooth ride.
Double-eye leaf springs attach to hangers that are welded onto your trailer. One end of this spring will attach directly to the hanger with a suspension bolt. The other end will attach to shackle straps that are suspended from a hanger. These straps allow the spring to move and pivot so that it can better compensate for uneven pavement. If you have a tandem- or triple-axle trailer, the shackle straps will be attached to the equalizer that connects multiple springs.
To mount this spring, you will need hangers, shackle straps, and suspension bolts. If you are simply replacing a spring, you may still have hangers welded onto your trailer. You should, however, replace your shackle straps because they are usually the first component to wear out. You may choose to replace old suspension bolts as well. It is recommended that you replace the other leaf spring in your setup at the same time. Because springs can sag and elongate as they wear, this new spring may not exactly match the old one, and the alignment of your trailer could be affected.
If you are fabricating a trailer, you will need to purchase a hanger kit for installation. To determine the type of hanger kit that you need, you must know the specific type of leaf spring that you have, as well as your axle capacity. Depending on the hanger kits used with them, springs can be configured to work for single-, tandem- or triple-axle applications. Hangers and other suspension components can also be purchased separately if there isn't a complete kit that works for your setup.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hello, everybody, this is Jeff at etrailer.com. Today, we're gonna take a look at the Dexter 25 3/8 inch long 5-Leaf Double-Eye Spring for the 6,000 pound trailer axles. Now, this leaf spring will act as part of your trailer's suspension system. Basically, it'll provide the attachment point for your trailer's axle, has multiple leaves to allow flexibility to absorb road shock, and this one would have five leaves. Allows for a nice, smooth ride, reduces wear and tear on the trailer, and it'll ensure a level ride on any bumpy or uneven surfaces. Now, the length we had mentioned is always measured from the center of one eye to the center of the other when it's unloaded, like it is now.
So, what we're gonna do is take a tape measure, from center to center and measure 25 3/8 inch measurement. The width on the spring is 1 3/4 inches. This is a sturdy steel construction. You could see the nylon bushings are installed included. The eye diameter when the bushings are installed 9/16 of an inch.
Now, the pre-mounted hangers are the aftermarket hangar kit, which is required for installation, those items we do sell separate on our website. Basically, this spring will attach to your hanger that's mounted on the trailer frame at one end, and then on the other end it connects to shackle straps, which are suspended from either a hanger or equalizer. This is for a quantity of one leaf spring. Spring capacity is 3,000 pounds, so when this is matched with one on the other side of the axle, it'll meet the 6,000 pound axle capacity. Now, there are additional dimensions on this spring that are listed on the product page if you do need them.
That should do it for a look at the Dexter 25 3/8 inch long 5-Leaf Double-Eye Spring for 6,000 pound trailer axles.
Do you have a question about this Trailer Leaf Spring?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.