Fulton F2 Swing-Up Trailer Jack, Dual 7" Wheels, Sidewind, Bolt-On - 1,600 lbs
(480 reviews)
Price: $225.14
In Stock
Fulton F2 Swing-Up Trailer Jack, Dual 7" Wheels, Sidewind, Bolt-On - 1,600 lbs
Item # F1413020134
Retail:$407.47
Our Price: $225.14
You Save: $182.33
This item qualifies for Free Shipping
In Stock
Need help with installation?
Locate installers near me- All Info
- Reviews (480)
- Q & A (0)
- Photos
- Used (1)
- Why etrailer?
Fulton Trailer Jack - F1413020134
- Side Frame Mount Jack
- 1001 - 2000 lbs
- Sidewind Jack
- No Drop Leg
- Bolt-On
- Swivel Jack - Pull Pin
- 10 Inch Lift
- With Wheel
- Fulton
Maintenance-free, corrosion-resistant jack is made for marine, recreational and utility trailers. Features aluminum alloy construction, adjustable mount and swivel system and twin-track wheels that roll independently to aid in maneuverability.
Features:
- Adjustable mount and swivel system for easy lifting and transport
- Can be adjusted to any height for mounting
- Swivels into position simply with the integrated, easy-to-grip pull pin
- Maintenance-free construction
- Lubricated, 1-piece gearbox eliminates the need for manual lubrication
- Ventilation port allows you to add extra grease if desired
- Twin-track wheels roll independently for easy maneuverability
- Wide wheel base allows for increased stability
- Anodized finish on inner and outer aluminum alloy tubes prevents rust even in the harshest environment
- Sidewind handle is made of strong plastic for durability and ease of use
- Wheel stop is included with caster
- Bolt-on installation
Specs:
- The included hardware fits 3"x3" and 3"x4" tongues
- Bracket height:
- 12-1/4" Retracted
- 22-1/2" Extended
- Lift height: 10"
- Wheel diameter: 7"
- Pull pin diameter: 9/16"
- Outer tube width: 2 3/4"
- Capacity: 1,600 lbs
- Lifetime limited warranty
How to Determine the Lift Capacity You Need in a Jack
A trailer jack is designed to lift the tongue of your trailer so you can connect the trailer coupler to your hitch ball. To do this, you'll need a jack with a lift capacity high enough to handle your trailer's tongue weight.
Tongue weight is the amount of weight that your trailer applies to the back of your tow vehicle. Typically, your tongue weight should be 10-15% of your total trailer weight (trailer + cargo). In other words, a 10,000-lb trailer would have a tongue weight between 1,000 lbs and 1,500 lbs. For a trailer this size, you would need a jack with a lift capacity of at least 1,500 lbs.
It's okay to have a jack with a weight rating that is higher than your trailer's tongue weight. In fact, a jack with a higher lift capacity should operate more efficiently, allowing you to spend less time cranking and more time camping.
Trailer and Camper Jack Lift
Every jack offers a certain amount of lift or travel. Screw travel is the distance the jack extends when you crank it (or toggle it to "extend" on an electric model). Some jacks include a drop leg for extra adjustability. On these jacks, you'll see the maximum extension of the drop leg listed in the specs as well. Adding the screw travel and drop leg travel together will give you the total lift. The total lift listed above can help you determine how high this jack will be able to raise your trailer.
1413020134 Fulton F2 Marine and Recreational Jack for 3" x 3" and 3" x 4" Frames, Sidewind, Twin Track, 1,600 lbs
California residents: click here
Customer Satisfaction Score:
96% were satisfied with this product
4% of customers were not satisfied
- Wrong item was ordered
- Arrived Damaged
- Product did not meet expectations
Customer Reviews
Fulton F2 Swing-Up Trailer Jack, Dual 7" Wheels, Sidewind, Bolt-On - 1,600 lbs - F1413020134
Average Customer Rating: 4.8 out of 5 stars (480 Customer Reviews)
Maintenance-free, corrosion-resistant jack is made for marine, recreational and utility trailers. Features aluminum alloy construction, adjustable mount and swivel system and twin-track wheels that roll independently to aid in maneuverability.by: Craig G.08/03/2014
This is a great jack. My previous jack(rated to 1200lbs.) was bent after raising the back end of the boat trailer to replace broken leaf springs and that's why I ordered a heavier duty jack. I really like the piece that keeps the crank from rotating while trailering and the dual wheels make it much easier to push/reposition the boat while it's being stored inside. The previous jack was a weld on mount so the installation was more involved. I didn't go with another weld on jack because none of the available weld on type jacks matched the hole positions on the existing weld on plate and I didn't want to deal with getting a welder to install/weld a new plate to the trailer frame. I ground off the plate from the trailer frame and smoothed the surface where the weld beads were. The u bolts that came with the new jack were too small to fit around the trailer frame so I drilled holes through the frame and was able to easily mount the jack with the u bolts provided. The jack works like a charm and looks great too. It was an excellent choice.
Comments
The jack has performed excellently since I installed it. I am very pleased with it and it just feels so much sturdier than the original jack. The extra cost to purchase a heavier duty jack wasnt a whole lot more and I really like the confidence it gives me knowing it is stronger. It also cranks smoother with less effort. Couldnt be happier with my purchase. Thanks Rachael.
Craig G - 08/05/2015by: Michael11/13/2022
Great purchase! Very happy , strong so far and definitely goes up straight no lean , my boat is a 24 grady white, eith fuel vlose to 8000, jacks no problem, i put the boat off the trailer in winter and this jack did its job no problem! U wont be disappointed
by: Charles08/11/2022
Very disappointed. The wheels would not roll or rotate. Immediately took it off. And expensive piece of scrap metal.
Comments
Sorry to hear this Charles. This type of trailer jackmeaning the double wheels needs to be mounted so that equal pressure is on both wheels. If one side gets more than the other it can cause issues like binding up or not wanting to roll. Also I would make sure that the trailer is loaded properly and you dont have to much weight on the tongue.
-- 
David B - 08/30/2022by: Steve B01/04/2017
The trailer jack f2 arrived in perfect shape at a very competitive price. The quality of the product was surpassed only by the fabulous customer service. I teach sales training and customer training and I have a new example of excellent customer service to present to my classes. More purchases to follow. The jack is installed on an all aluminum diamond plate show trailer for my Canam Spyder F3 trailer. The style of the all aluminum jack compliments the trailer.
Comments
It’s working fabulously. Best feature is the locking wheel which really stops the trailer without a chock. Classy appearance compliments my all aluminum trailer
Steve B - 01/04/2018by: Stephen 08/12/2022
High quality and easy install. I use it for my 26’ enclosed trailer. It’s a winner!
by: Gary D06/06/2014
This Jack was on my Tricker Trailer when new. Broke the gear inside and replaced it with a cheaper jack..... you get what you pay for. Looks good, works good and now that I found etrailer.com I can order parts as needed. Etrailer has great Customer assisantant and follow up was exceptional.
by: Jimmy08/07/2022
Easy install! Supports trailer while rolling! Works great!
by: Jonathan 10/30/2022
Awesome customer service!
by: Patrick09/03/2020
Wow. I cringed on the price but what a great tongue wheel. The double wheels roll very smooth and it looks on my custom trailer
by: Boyd03/11/2022
I haven’t put your trailer jack on my boat trailer yet, but I know you have an awesome product compared to the cheapy ones I’ve been using in the past
by: Mark04/23/2016
Overall a very good product so far. I have only used it for a little under a year, but have had no mechanical issues with it. The crank works well, the wheels roll ok for holding up a 23' fiberglass Hurricane. The only minor design change that I would make would be to the placement of the unlocking pin. Being that it is tight to the inside of the trailer tongue makes it harder to grab and can become a knuckle scraper.
by: Grimdiver03/17/2020
I installed this jack on a 22' boat trailer due to having 2 previously installed jacks fail. No such problems with this jack. It really is heavy duty. I can now maneuver the boat tongue around without the jack collapsing. Great product and I wouldn't hesitate to buy another one.
Comments
OK, so its been a year now with the Fulton Jack and I still think it is the best one I have ever owned.
Ken E - 03/18/2021by: Jonathan 08/31/2022
Fast shipping and great service. Thank you!
by: Mako 24306/12/2015
I've used Fulton trailer jacks for over 40 years. The F2 1600 lbs rated jack is the finest one they've designed to date. It lifted my trailer with a 3 ton boat with ease. It does jack up and lower faster than my old Fulton. I'm very pleased with this one, plus it was offered by etrailer.com at a much more reasonable price than West Marine.
Comments
I bought two of these Great trailer jacks and both boats couldnt be happier. Good construction. Jacking is faster than my old ones. Couldnt be more pleased. Thank you for offering a good quality product. And better price the West Martine.
Mako 2 - 06/11/2016by: Jerry W01/24/2020
What a great jack! Smooth operation and lots of inquiries as to where I purchased it. Thanks to my wife, I am the only one at the boat ramp, but that will probably change soon!
by: Bruce01/31/2019
just received my trailer winch and jack. outside temperature was -1o F this am so no chance to mount or use yet but wanted to say how please with prompt service and delivery
Will use again
Comments
Both winch and jack performed as expected with issues and easy to install.
Bruce G - 02/03/2020by: Dave12/19/2016
Fulton F2 jack and F2 winch Came today! on trailer and ready to go to the river on Wednesday. Easy to assemble A Big Thanks to George at E-trailer, will order again. Thanks Dave.
Comments
Great
Dave - 12/19/2017by: Tore01/06/2018
Right now it's too cold to work on the trailer, January in NY. This is my second order with etrailer and ther were no problems I got what I ordered on time and have no qualms recommending them.
Thank You
Tore
Comments
Everything is working well. The parts were used on a Trailor for my smoker.
Tore - 01/08/2019by: Juan06/04/2018
Best trailer jack for salt water use I ever bought! And I have bought plenty! Until this one, most other brands rust out and lock in a little as a year. This one is worth the money! Only thing I wish the plastic wheels would be a little bit more robust.
George from etrailer is awesome when it comes to customer service and ensuring customer satisfaction. etrailer exceeded my expectations. THANK YOU George!
by: Paul A.11/13/2014
Excellent trailer jack. Dual wheels lock to prevent movement. Square lift tube prevents wheels from spinning when not in contact with ground. Swing mechanism works well. Very heavy duty construction. Handle is plastic but must be lexan or something similar because it's incredibly strong. Worth every dollar.
by: Hugh06/23/2021
They kept me informed on this part that was on back order . They also sent emails on items available in case I wasn’t willing to wait, this was helpful. When the part was on its way they promptly informed me of the shipment and ETA of that item.
This was the kind of information anyone making a purchase would want…they did a fantastic job
by: Alan B05/18/2012
I have 7 trailers and this jack is the most adaptable to any application that it may be used for. The bolt-on F2 jack is adaptable to either a 3" or 4" frame also has a vertical adjustment to get the most out of jack travel. It appears to be marine grade, I am using it on my 25' pontoon boat trailer. It has a easy locking wheel piece that keeps the easy rolling dual wheels from moving. It is one of the best engineered jacks on the market I feel.
by: Kevin04/23/2020
I just installed this tongue jack on my snowmobile trailer. It is definitely a well engineered burly product - heavier than I expected. The installation was straight forward with no surprises. Everything need was provided. The trailer is in storage until next season, so I can't offer any further information at this time. I will probably buy another one for my boat trailer. These are absolutely better than the cheap light weight jacks on most trailers.
by: Robby02/28/2017
Just got the trailer jack, fast service and shipping. Haven't got it mounted yet.
Comments
Still a great product, thanks
Robby - 03/05/2018by: Bill S.12/26/2013
I bought it because I needed to have a low mount and this one is adjustable. It bolted on fine but as for operation I have a few concerns. The locking pin does not snap into place when you rotate it to the locking position. You have to wiggle the lock pin and assembly at the same time to get it to lock. The double wheel does not swivel into the right direction like a caster should. You have to kick it into the direction first. Otherwise it looks like it is well constructed just lousy operation.
25
480
Show More Reviews
See what our Experts say about this Fulton Trailer Jack
- What are the Mounting Hole Distances on the Fulton F2 Swing-Up Trailer Jack, # F1413020134I went out to the warehouse to measure the mounting plate on the Fulton F2 Swing-Up Trailer Jack, Dual 7" Wheels, Sidewind, Bolt-On - 1,600 lbs # F1413020134. The mounting holes are 3-1/2 inches (top to bottom) and 4-1/2 inches (left to right) apart on center.
view full answer... - Can the Fulton F2 Swing-Up Trailer Jack Be Mounted to an I-Beam Aluminum Boat TrailerFirst, the closer you get to the axle on the trailer, the heavier that part of the trailer is going to be. That is important because where you mount the jack could determine if it is over or under capacity. You would need to box out the frame so that it is square or rectangle and not an I so the jack can be safely attached. Usually to do this, you would weld on a couple of steel plates. However, welding to aluminum is tricky and requires a very skilled welder with experience. This is probably...
view full answer... - Dimension of Fulton F2 Swing-Up Trailer Jack WheelsI went out to the warehouse to measure the overall width of the wheels at the base of the Fulton F2 Swing-Up Trailer Jack # F1413020134. Each wheel is 1-3/4 inches thick. Overall, from outside to outside, the wheels have a diameter of 5-1/4 inches.
view full answer...
- Trailer Jack Replacement Recommendation for a 2015 T and G Little GuyThe Fulton F2 Swing-Up Trailer Jack # F1413020134 would work well for you as long as your trailer has either a 3"x3" or 3"x4" trailer frame. You would just need to mount it to the side of your frame and you would have a replacement jack for your damaged one.
view full answer... - Spacing of Mounting U-Bolt Holes on Fulton F2 Trailer Jack # F1413020134The U-bolt mounts of the Fulton F 2 # F1413020134 will accommodate 3x3 and 3x4 trailer tongues . When the holes are measured center to center, they measure exactly 3.44 center to center and 4.44 center to center, which in the closest fractional measurement would be 3-7/16 apart and 4-7/16 apart. You can see these dimensions on the photo I edited for you.
view full answer...
- Recommended Trailer Jack for 23 Foot Fishing BoatWhen choosing a jack, you will want to choose a jack that can support the tongue weight of your boat trailer and a jack that has an appropriate lift height for your trailer. Typically, the tongue weight on boat trailers does not exceed 15 percent of the gross trailer weight. Be sure you verify the tongue weight capacity of your trailer before selecting a jack. I have included a FAQ article about measuring tongue weight for you to check out. If you still have your old jack, you can go...
view full answer... - Fulton F2 Jack Recommendation for a Fishing Boat TrailerThe Fulton F2 Trailer Jack part # F1413020134 that you referenced is a great jack that has a 1,600 lb capacity. Since your trailer's tongue weight would be far less than that this jack would work great for you. This jack also has a limited lifetime warranty. This jack fits 3"x3" and 3"x4" tongues. Check out the review video I attached for this jack for more info.
view full answer... - Will Fulton F2 Swing-Up Trailer Jack # F1413020134 Fit on 3 x 3 Trailer FrameYes, you can use the Fulton F2 Swing-Up Trailer Jack # F1413020134 on your trailer that has a 3 x 3-inch frame member. It is intended to fit 3"x3" and 3"x4" trailer tongues .
view full answer... - Information About Fulton F2 Swing-Up Trailer JackThe Fulton F2 Swing-Up Trailer Jack, part # F1413020134 has a limited lifetime warranty and that is included in the packaging with the jack. This jack has a 1600-lb capacity and is designed to fit 3x3 and 3x4 trailer tongues. The mounting hardware is included. The jack has dual 7-inch wheels and a lift height of 10 inches.
view full answer... - Dimensions of Fulton F2 Jack F1413020134The Fulton F2 Swing-Up Trailer Jack # F1413100334 has a moveable mounting bracket (not shown in the photos) that provides an adjustment range of 8-inches. When extended fully the distance from the pivot center to the wheel center is 17-1/4-inches; when retracted it is 7-1/4-inches. From the top of the jack to the center of the pivot (with the sliding bracket at its lowest position) the distance is 14-5/8-inches.
view full answer...
- Troubleshooting Fulton F2 Trailer Jack with Dual Wheels that Will Not Roll StraightThere's a few things that could be going on here. The most likely is that you need some weight on the trailer. With the dual wheels when the trailer is being moved the wheels have such a tight connection to the tube that it only takes an extremely slight bump in the road to disrupt them. Weight on the trailer will prevent this because the downward force keeps the wheels on the ground. Another possibility is the mounting of the jack. If the plate is not 100 percent vertical (which isn't...
view full answer... - Can I Use a Fulton F2 F1413020134 to Move my Trailer a Couple of FeetThis jack is going to be a great solution for your needs. The wheels are designed to help you move the trailer around to help get it hooked up to your vehicle. The dual &" wheels are designed to make this easy be rolling over any small cracks or rocks that may be in the way. It is recommended that when moving your trailer that you have the jack retracted some you don't want to be pulling it around all of the way extended because you'll be putting a lot of stress on it. With your trailer...
view full answer...
- Does the Handle on the Fulton F2 Swing-Up Trailer Jack, part # F1413020134 Hit the TrailerI don't see this being a problem at all. As you can see in the video the Fulton Jack part # F1413020134 below it mounts to the outside of the frame and the handle is a long way from any part of the trailer. They may be talking about the swing up release being pretty tight to the trailer as seen in the photo below. That release is fixed however so there again wouldn't be any issue with ramming your hand into the trailer.
view full answer...
- Could Fulton F2 Swing-Up Trailer Jack Weld to Aluminum Trailer FrameWelding steel to aluminum isn't impossible but it's pretty challenging. If you wanted to weld Fulton F2 Swing-Up Trailer Jack # F1413020134 to an aluminum trailer I would recommend check with welders near you to find one who has the skills and equipment to do so.
view full answer... - Will Fulton F2 Swing-Up Trailer Jack Replace Original F2 Trailer JackYes, the jack will bolt onto the mount of your original Fulton F2 jack. The Fulton F2 Swing-Up Trailer Jack # F1413020134 will mount to bolt holes that are 4-1/2" wide x 3-3/8" tall on center, which is what your mount will be for an F2 jack. I have added a link to a video review for you to check out as well of the Fulton F2 Swing-Up Trailer Jack # F1413020134.
view full answer...
- Height of Fulton F2 Swing-Up Trailer Jack When Fully RetractedI went out to our warehouse to take a look at the Fulton F2 Swing-Up Trailer Jack # F1413020134 referenced in your question. I measured an overall height with the jack at its shortest position, fully retracted, of right at 25 inches. I have attached an image with this dimension labeled that you can also take a look at. This is a really nice, corrosion-resistant jack that features an adjustable mount and swivel system to allow for easy lifting and transport. It has a 1,600 pound weight...
view full answer...
- Plastic Housing Replacement Availability on Fulton F2 Trailer JackThe Fulton F2 Swing-Up Trailer Jack # F1413020134 (as well as other F2 jacks) has that plastic piece that as you referenced is #9 in the exploded diagram. I reached out to my tech contact at Fulton and unfortunately that is not a replaceable part. You will need to replace the entire jack.
view full answer...
- How to Change Height of Fulton Jack Mounting BracketTo adjust the height of the mounting bracket on the Fulton F2, part # F1413020134, you need to loosen the bolt behind the bracket (which it sounds like you have) as well as the bolt in the middle of the bracket. Take a look at video that I have attached for you. Make sure to tighten both bolts back to spec per the instructions after adjusting the height.
view full answer... - Availability of Replacement Gears for a Shelby 5759 Trailer JackWe do have replacement jack options for you, but unfortunately we do not have any replacement gears for a Shelby jack. I have attached a link to our selection of swivel jacks that you can filter through for the best replacement option. One of the most popular options that we have to offer is the Fulton F2 Swing-Up Trailer Jack # F1413020134 rated for 1,600 lbs. This jack has two 7" wheels that make it easy to maneuver and features an easy bolt-on installation that fits 3"x3: and 3"x4"...
view full answer... - Recommended Replacement Bolt-On Jack For Boat TrailerI do not have a Jack that exactly fits your trailer frame dimensions. However, a close match that should work is the Fulton F2 Swing-Up Trailer Jack with Dual Wheels Item # F1413020134. It has hardware for 3 inch x 3 inch and 3 inch x 4 inch trailer tongues. If the included u-bolts do not secure the Jack to your trailer frame then you could get different sized u-bolts that do (we do not have any smaller selections). This Fulton Jack is an adjustable mount with an easy to use swivel...
view full answer... - Can the Fulton F2 Swing-Up Trailer Jack # F1413100334 be Used for a Boat Trailer and 21 ft BoatThe Fulton F2 Swing-Up Trailer Jack, Dual 7" Wheels, Sidewind, Bolt-On - 1,600 lbs # F1413020134 that you referenced has a weight capacity of 1,600 lbs so it should work great for your 21 ft boat. As long as the loaded tongue weight of your trailer is under the 1,600 lb mark you are good to go. This jack comes with mounting hardware for 3 "x 3" or 3" x 4" tongues. I have attached a video of this jack for you.
view full answer... - Bolt Pattern Dimensions of Fulton F2 Swing-Up Trailer JackThe bolt hole dimensions on the Fulton F2 Swing-Up Trailer Jack # F1413100334 are 3.44 inches by 4.44 inches center-to-center, according to Fulton. It will fit on a 3" x 3" or 3" x 4" trailer tongues and has a 1,600 lb capacity. I've added a link to a video review of this product for you to take a look at.
view full answer...
- Mounting Bracket for Fulton F2 Trailer Jack # F1413020134The mounting bracket for Fulton F2 jack # F1413020134 uses u-bolts and fits 3x3 or 3x4 inch frames. It bolts on to the side of your frame. If you do choose to weld-on that bracket, you would use part # F500320 and the welding should be performed by a professional welder. Take a look at the install video for your jack and see if that clears things up for you.
view full answer... - Solution for Fulton F2 Trailer Jack with Broken Inner LegThe inner leg of the Fulton F2 Swing-Up Trailer Jack # F1413020134 that you referenced is not a replaceable part. Only solution would be to replace the jack with a new one.
view full answer...
Do you have a question about this Trailer Jack?
Why etrailer.com?
At etrailer.com we guarantee:Real product know-how.
We make sure that the products we sell are what we say they are, and that they work the way they are supposed to work. Get real advice from a real person who has the knowledge and expertise needed to solve your problem.Most detailed, accurate trailer jack information available.
Because we take providing accurate product information seriously, we take our own detailed product photos, demo videos and installation videos, as well as verify measurements, instructions, and vehicle fit information.Installations, made easy.
We love helping people and have the most highly-trained customer service, hands-on experience, step by step videos and installation instructions.Fast shipping.
Your order is automatically routed to get out of our warehouse and to your door as quickly as possible. Receive free shipping on orders over $99.Personalized service for life.
We provide one-on-one, personalized service from the ordering process through the life of your product.Trusted since 1946.
We've been serving customers since our parts store first opened in 1946 and continue to be recognized by our customers, our vendors and third parties for exceptional service.Returns Policy
Need to return an item? No problem. Please read our Returns Policy for more information.
Info for this part was:
Expert Research:
Jackie C
Expert Research:
Mike L
Expert Research:
Robert G
Expert Research:
Michael H
Expert Research:
Jameson C
Expert Research:
John H
Expert Research:
Adam R
Expert Research:
Jeffrey L
Updated by:
Adele M
Updated by:
Laura H
Updated by:
Lisa S
Updated by:
Shelly K
Updated by:
Wilson B
Updated by:
Alexander C
Updated by:
Mike S
Video Edited:
Dustin K
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-636-306-4830
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.