Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"

See what our Experts say about this CURT Trailer Hitch

• Replacement Trailer Hitch Receiver for OEM Receiver on 2004 Chevy Silverado 2500HD
  As long as you don't have the 10" deep drop bumper on your 2004 Chevy Silverado 2500HD the trailer hitch you need to replace your OEM is the Curt Trailer Hitch Receiver # 13210. The design looks a little different but it still has a hidden crosstube and the bracket above the receiver like what you have on your hitch from the factory.
  view full answer...
• Correct Curt Class III Trailer Hitch for a 2009 GMC Sierra 2500 6.5' Bed
  The correct Curt Trailer Hitch Receiver with class III rating for a 2009 GMC Sierra 2500 with 6-1/2' bed is part # 13210. This hitch is a direct bolt-on with drilling required. It has a 6,000/600 lb weight capacity which can be increased with a weight distribution system. The trailer hitch options for this vehicle will tie into the bumper.
  view full answer...
• Should EZ Lube Spindles Have Grease Installed Through Zerk Fitting
  There are a couple schools of thought on the use of EZ lube spindles for putting grease in hubs. I personally wouldn't pump them full of grease until the old grease pushes out as I'd be afraid to blow out the seals. Since this is a pretty common problem I'd stay cautious and pack them by hand like your tech told you. Maybe when it's all packed and reinstalled you could put one pump or a half pump if you felt like more was needed. I'd also wait to regrease the hubs like the tech mentioned...
  view full answer...
• Is Transmission Cooler Required for towing with 2006 Honda Odyssey
  Based on my research, a transmission fluid cooler and a power steering fluid cooler are both required for towing with your 2006 Honda Odyssey. I recommend the Derale Series 8000 Plate-Fin Transmission Cooler Kit # D13503. This is the largest transmission cooler we have to fit your Odyssey, measuring 11 inches wide x 8-3/4 inches tall x 7/8 inches deep. The larger the cooler, the more efficiently it will cool the transmission fluid. You cannot cool the fluid too much. This transmission...
  view full answer...
• Replacement Hubs for EZ Loader Model EZNB 14-17 1650 Boat Trailer
  The correct galvanized replacement hubs for your EZ Loader EZNB 14-17 1650 trailer are # CE13315. The hub includes bearings, races, the grease seal, replacement cotter pin, dust cap and lug nuts.
  view full answer...
• Replacement Hub Recommendation for EZ Loader Boat Tariler with 5 Lub Wheels
  Thanks for the photo! Using the VIN I was able to gather the necessary information needed to help you find the correct idler hubs. For this, I recommend the CE Smith Trailer Hub Assembly part # CE13311. This hub uses a L44649 inner/outer bearing, 12192TB grease seal, and has a 5 on 4-1/2" bolt pattern. This will be a direct replacement for the idler hubs you have on your trailer now and even comes pre-greased.
  view full answer...
  
• Recommended Transmission and Power Steering Cooler for 2017 Kia Sedona LX
  In order to add a transmission cooler to your 2017 Kia Sedona LX, I recommend the Derale Series 8000 Plate-Fin Transmission Cooler Kit part # D13504 which will be plenty for your Sedona LX. The plate fin cooler will do a good job of dispersing any heat that might build up in the fluid and keep your transmission from overheating while towing. For a power steering fluid cooler you can use the Derale 2-Pass Tube-Fin Power Steering Cooler with Offset Mounting Bracket - 8-1/8" Wide # D13210...
  view full answer...
• What Diameter Spindle Does CE Smith Trailer Have
  The correct replacement hub for the CE Smith Multi Sport Trailers like part # CE48810 is the CE Smith Trailer Hub Assembly part # CE13210 which does have 1 inch diameter spindle where the bearings ride.
  view full answer...
• Can 2009 Honda Odyssey Tow 2,000 Pound Loaded Camper
  As long as you stay under the towing limits listed in your owner's manual (which you have already checked) then you will have no problems towing your Viking Epic 1906 Camper. With that being said I did take a look at the online version of the owner's manual for your 2009 Honda Odyssey and found that the listed towing capacities are only if the vehicle is equipped with a transmission cooler and power steering cooler. Especially since you will be doing a lot of uphill towing, adding these...
  view full answer...
• How To Determine If Replacement CE Smith Hub CE13210 Fits Trailer
  To figure out if the CE Smith Trailer Hub # CE13210 you'll need to find your axle capacity and bearing combination, I have no way of looking this up via your vin. The easiest way is looking for the axle tag on the center of the axle beam, as I can use the information on that to identify the axle and bearing combination. Depending on the age of your trailer that tag may be missing in which case you'd need to use digital calipers # PTW80157 to measure the spindle in the locations shown...
  view full answer...
• Replacement Needed for the Titan Hub T1721400042
  I have a potential alternate option, but unfortunately, the Titan Trailer Hub Assembly for 2,500-lb Axles - 5 on 4-1/2 - Cast T1721400042 is no longer available from the manufacturer. As this uses an uncommon combination of inner and outer bearings, I recommend replacing the axle with a more common set up. With that said, the Dexter Trailer Axle with Idler Hubs - 5 on 4-1/2 Bolt Pattern - 89" Long - 3,500 lbs # 35545I-ST-89 will come with idler hubs and includes all bearings, seals, caps,...
  view full answer...
• Correct Replacement Idler Hub and Bearing Kit for CE Smith Multi Sport Trailer CE48810
  The correct replacement idler hub for the CE Smith Multi Sport Boat and Kayak Trailer part # CE48810 is the CE Smith Trailer Hub Assembly part # CE13210 or if you are just looking for a bearing kit it's the Bearing Kit with Grease Cap part # DL21792.
  view full answer...
• CE Smith Multisport Trailer Wheel Bearing and Hub Replacement
  The CE Smith trailer # CE48870 that you referenced would use the bearings # L44649. If you ever needed a replacement hub you'd just need the part # CE13210.
  view full answer...
• Replacement Hub to Replace Oil Bath with Grease Lubed Bearings
  I have a solution for you. However, you are going to need a little more information to make sure you receive the correct hubs to replace you current oil bath hubs. You will need the bearing numbers of your current hub to match with the replacement grease hubs we offer. If by chance the numbers are worn off or not printed on the back of your wheel bearings, then you will have to measure the inside diameter of the bearings. The attached picture will show you what measurements will help in...
  view full answer...
  
• Replacement Hub Assemblies For 2500 lb Axle For Use With Grease
  We can't determine what bearings and race you have based on a serial number. If they are in fact 2500 lb axles, that significantly narrows down our options. You will want to check the bearing numbers on the face of the inner and outer bearing of one of your hubs to determine fit. All of our 2500 lb hubs are 5 on 4-1/2 inch bolt pattern and have the same bearing for both inner and outer application. For both inner and outer bearing # L44643 (1 inch diameter) you can use the CE Smith...
  view full answer...
• Replacement Hubs for 2006 Aliner Expedition Folding Camper with 2.5K Axle
  A 2500 lb axle would typically feature a spindle that's compatible with the L44643 inner and outer wheel bearing. I'd recommend checking the bearing cages on your existing bearings for the reference number just to confirm. We offer 2500 lb capacity compatible idler hubs with a 4 on 4 or 5 on 4-1/2 inch bolt pattern. For a pre-greased hub compatible with a 4 on 4, I'd recommend the # CE13110 or for a 5 on 4-1/2 inch bolt pattern, use part # CE13210. The hubs are sold individually, bearings,...
  view full answer...
  
• Replacement Idler Hubs for 2500 lb Axle With 5 on 4-1/2 Bolt Pattern
  The 2500 lb axle uses a straight spindle which is compatible with either the L44649 or L44643 inner and outer bearings. Your existing bearings will have the reference number etched into the side of the bearing cage for easy identification. We have one 5 on 4-1/2 inch bolt pattern option for each bearing set. If you have the L44649 bearings, use the Timbren # TA88545-2 which are sold in pairs only. If you have the L44643 bearings, use the CE Smith # CE13210 which is avilable individually. Either...
  view full answer...
• Recommended Replacement Hub For A CE Smith CE48870 Trailer
  I contacted CE Smith and the # CE48870 Multi Sport Plus Boat and Kayak Trailer does use the larger 1-1/16" spindles due to its larger size and capacity. The CE Smith # CE13210 hub is designed for use with the 1" spindle, so it will not be compatible with your trailer, unfortunately. With that said, you will have 2 options. First, you can replace the hubs with the # CE13311 kit. This will include everything the same as what you have, but will have the larger bearings to fit over the spindle....
  view full answer...
• Hubs for 2,500 Pound Axle with Straight 1 Inch Spindle
  The Timbren Idler Hub Assembly # TA88545-2 referenced in your question is designed for 2,500 pound axles and it uses the # L44649 inner and outer bearing. This particular bearing features an inner diameter of 1.063 inches, so I highly recommend verifying the measurements you took on your spindle with a digital caliper. If you do have 2,500 pound axles and the spindle is in fact 1 inch exactly, then the correct idler hub assembly will actually be the CE Smith # CE13210. This hub uses the...
  view full answer...
• Replacement Bearings for a Dico 40511 Hub and Drum
  We can definitely get you replacement bearing kits for your Dico 40511 brake drum, but I was unable to find out what it originally came with, unfortunately. So with that being said, you will need to either measure the inside diameters of both the inner and outer bearings to confirm the parts needed, or see if there are part number stamped into them. These part numbers do wear off over time, however, so measuring may be the way to go. This should also be done with calipers, like the Performance...
  view full answer...
• Replacements For Hadco Trailer Axle With Hadco 3109 Hubs
  Though we do have the replacement bearings, races, and seals available for your Hadco 3109 hub (which I have listed below), the combination used will not have an equivalent replacement hub available, unfortunately. Replacement Trailer Hub Bearing # 501349 Replacement Race for 501349 Bearing # 501310 Replacement Trailer Hub Bearing # LM67048 Replacement Race for LM67048 Bearing # LM67010 Grease Seal # 1105-100-035 If you are wanting to replace the whole hub though, your best bet will be...
  view full answer...
  
• What is Required for Towing a Trailer w/ a 2004 Honda Pilot
  I looked up an online version of your 2004 Honda Pilot's owner's manual and it states that additional transmission and power steering coolers are required to tow. It also states that a trailer that weighs 1,000 pounds or more should have its own operating brakes. I've attached an article on coolers that you might like. The firs thing in choosing one is find a place to put it in your Pilot. The best place is always in front of the radiator so it will get as much air flow as possible....
  view full answer...
• How to Choose the Correct Pre-Greased Replacement Hub for Snowbear Trailer
  There are pre-greased hubs available in a 5 on 4-1/2 bolt pattern. In order to find the correct replacement hub you can take apart your good hub assembly and look at the bearings themselves; wipe away the grease and you should be able to see the part number stamped directly on them. If your hub has inner and outer bearings # L44643 you'd need CE Smith Trailer Hub Assembly w/ Carrying Case for 2,500-lb Axles - 5 on 4-1/2 - Pre-Greased # CE13210. Should your hub have inner and outer bearings...
  view full answer...
• Replacement Hub for Boat Trailer Using L44643 Bearings
  Assuming you have a # L44643 inner and outer bearing, the correct bearing kit is the # BK1-100. The hub will depend on the bolt pattern you need. These hubs will come pre-greased and include the bearings, races, and grease seals. For a 4 on 4 I recommend the CE Smith Trailer Hub Assembly w/ Carrying Case for 2,500-lb Axles - 4 on 4 - Pre-Greased # CE13110. For 5 on 4-1/2 I recommend the Trailer Idler Hub Assembly for 2K Axles - 13" to 15" Wheels - 5 on 4-1/2 - Pre-Greased # AKIHUB-545-2-LF-1K....
  view full answer...

Do you have a question about this Trailer Hitch?