Most Popular Fixed Ball Mount for 2016 Toyota Highlander

Not crazy about the clip in the 5/8" connecting pin, does not seem to secure enough for me. I ordered a locking pin to make a better connection.

This is a great ball mount for my Draw-Tite 2 inch hitch. It has a 1 inch ball hole and 5/8 inch pin hole. Mine came with the hitch pin, but I use a locking one that I purchased separately so it would be much harder for a would-be-thief to take. When not in use, I take it off and store it my trunk area. As with the Draw-Tite hitches, this ball mount is very well made and suited to the task of towing. Another great product at a great price!

Good hitch

I seldom take the time to write a review but I felt compelled to share my excellent overall experience with etrailer.com. I ordered the C13200 trailer hitch receiver, 2" ball, 2" ball mount receiver, pin/clip, and C56217 wiring harness for my 2017 Toyota Highlander XLE. All arrived in no time and in excellent condition. The installation videos and PDF documents are outstanding. I installed the hitch receiver in roughly 45 minutes - includes time to convince brother in-law to come over to help hoist it into place. Wiring harness installation was a breeze, roughly 20 minutes (again, great instructional videos). I could not be happier with the finished product. Thanks etrailer.com for making this a trouble free installation. If you are considering adding a hitch, etc. go no further, you are at the right place...order away. Its very easy to install and you will save a trailer load of cash!!!

The only thing I will have to say that it may be a bit too low to pull my fishing boat. I may have to reverse the ball orentation.

Trailer hitch looks great, will work great this spring for trailer hauling projects.

To be honest, I use it upside down. I needed a hitch with rise, but none were available at time of purchase, and yours, inverted, works perfectly! The welds are regularly checked and remain all secure. It's a good hitch.

Working in the sand and grass of my driveway my wife and I installed our new etrailer receiver hitch. Great fit and finish! Went right on as described in the online guide. Hitch required a spacer washer on top back bolt attachment point. Taped it on so it would not move while lifting in place and it stayed right there! Used a car jack to raise up and hold the hitch into the underside of the trunk tighten the bolts and reattached the tail pipe done. Now we can pull our Sunfish Sailboat any where the car will go.

Yes Laura its a good thing. But I do dismount it when not in use lest I smash someones bumper when backing into a parking space. .

We sold our small motor home and purchased a small travel trailer. This hitch provided a perfect solution to how to use our bike rack while towing the trailer. It even allows room for the pickup tailgate to be lowered without removing the bikes from the rack. The hitch is very hefty with a high weight limit - plenty for the GVW of the trailer (7,000#) plus 125# of rack and bikes.

Super solid mount at a great price. Just the right drop for my boat trailer.

Very pleased with etrailer. Very easy to order from website. Fast delivery, easy to install ,perfect fit . Thanks. .

My usage of your hitch is a bit unusual, I think. I pull a two ton roller with my Ram and I've used your cushioned hitch to smooth out the process. The roller Lunette just dropped over a 2" ball and then banged and jerked on the ball neck. Check out the photos for my adaptation.. I can flip it over and use the 2" ball! Have enclosed some photos. The cushion is holding up very well and it takes a beating!! Thanks

We have a Pink Tractor (google Mom's Pink Tractor) that we pull to events, mainly in Ks, Ok, Mo, and Ne. We have around 35 events a year we take the tractor to to promote breast cancer awareness. The other day my wife and I were leaving for an event, i had let a friend borrow the hitch to see how he liked it. In less then a mile from the house my wife started complaining about the trailer jerking. That is coming from a lady that really was upset when I paid that much for a hitch. She told me to stop and buy one. (a long and expensive trip, we had to stop at a casino so she could rest her neck) I could write a review with a lot of trailer talk, but, this story tells the story.

Heavy duty , very good quality.

I hooked up the draw bar today for the first time to the trailer that I built and the hitch I installed. The draw bar uses a cotter pin that slides on the bolt rather than going through a hole to mount the bar to the hitch. I have never used a sliding on pin in anything - I've only used those that go through a small hole matching the pin. This includes my farm tractor and other tools. I hope it is secure because it does slide on easily. The bar itself appears nice and strong.

We used our car hitch and cargo carrier last summer in a Honda Accord to support a cargo carrier. It held up great on a 4,000 mile camping/hiking trip from Mid Missouri to Glacier National Park, MT. We were able to use the carrier/hitch to carry our large tents and baggage (approx 120#)directly behind our car trunk. Initially I was a little hesitant at the smaller 1-1/4" tube hitch, but it was very stable throughout the long trip. Sure was a lot less drag than putting all our gear on a roof cargo carrier.

A small shipping glitch , but they took care of it quickly

I had a great experience ordering from you. Your organization kept me completely up to date with the order & shipping process and delivered the exact products I ordered. Attached is a photo of the 16,000 lbs capacity hitch and 30,000 lbs 2 5/16 ball you sold me in use. The boat and trailer total about 12,000 pounds. Thanks again.

Excellent product! With the three different ball sizes, this tri-ball mount gives you a lot of flexibility. Gone are the days of having several different ball mounts to fit different tongues. High quality construction makes this an excellent investment.

This item should solve the problem I have had with a stainless 3-way ball when I tried to reverse the position on the ball mount. The threads galled between the hex nut and hitch ball.

Works fine, maybe a bit too long of a drop for a 2022 Highlander Hybrid

Fast shipping

Purchased this hitch as a companion for our Reese anti sway control. The small ball for the Reese sway control fits in the bracket and the 2” drop on the hitch is exactly what we needed to have our Jayco camper level when towing.

Nice finish, hopefully will hold up over time. Unfortunately it is rather loose inside the 2" hitch hole, I don't understand how hard it is to get a tighter tolerance. We used some electrical tape as others suggested, but I would expect more from this brand.

Perfectly as described, Box was a heavy hitch and the box must have been damaged in shipping so it was a little delayed. You can't mess up a forged hitch it still is in excellent condition.

Arrived today. Fast shipping, and thank you for that! Seems to be a quality ball mount. Just what I needed to get the ball lower to tow my trailer. With this, now the top of the ball is at 16" where it needs to be. Custom built receiver on my old moving box van. Just need to weld on safety chain slots and paint it. Can't drop the lift gate with the receiver in (its pinned on both sides), but hey....I can tow now.

Tow infrequently; got new(to us) 2015 RAM 2500 pick up to tow our 38’ touring travel trailer. Have a HD WD hitch & adjustable sway control hitch set up we use for this trailer, but needed a drop hitch for our smaller Travel trailer& misc use haul trailer,,,,both much lighter & do not require the sway control set up. This drop hitch & ball fit the bill perfectly as the needed drop did not provide suffice t ground clearances to utilize the WD hitch mount setup (which was not needed) for those smaller loads. E-trailer worked w us to get the product we needed & an option that was inexpenve but sufficiently rated to pull our smaller trailers! Very happy our results !

Retail type stores only carry mainstream items so when I needed a special length ball mount for my 2011 Traverse I found the size and quality with Curt Products .

Recently bought a Kubota RTV x900. The receiver is located under the bed. With the extra long ball hitch drawbar I can easily get to the drawbar and use a clevis to hitch my 5ft. wide mower or attach a ball and use the trailer. The pictures will illustrate the length of the drawbar which makes access very easy. The product is heavy duty and well made. Ordered this product on Thursday morning and it was delivered the next day, Friday afternoon. Customer service was helpful, will use etrailer again. Thanks