Best 2011 Toyota Highlander Trailer Hitch Ball Mounts

Great product, great price, easy to find the right part online! Also shipping was very fast!

This is a great ball mount for my Draw-Tite 2 inch hitch. It has a 1 inch ball hole and 5/8 inch pin hole. Mine came with the hitch pin, but I use a locking one that I purchased separately so it would be much harder for a would-be-thief to take. When not in use, I take it off and store it my trunk area. As with the Draw-Tite hitches, this ball mount is very well made and suited to the task of towing. Another great product at a great price!

I seldom take the time to write a review but I felt compelled to share my excellent overall experience with etrailer.com. I ordered the C13200 trailer hitch receiver, 2" ball, 2" ball mount receiver, pin/clip, and C56217 wiring harness for my 2017 Toyota Highlander XLE. All arrived in no time and in excellent condition. The installation videos and PDF documents are outstanding. I installed the hitch receiver in roughly 45 minutes - includes time to convince brother in-law to come over to help hoist it into place. Wiring harness installation was a breeze, roughly 20 minutes (again, great instructional videos). I could not be happier with the finished product. Thanks etrailer.com for making this a trouble free installation. If you are considering adding a hitch, etc. go no further, you are at the right place...order away. Its very easy to install and you will save a trailer load of cash!!!

The hitch went on exactly as described in your YouTube video. I got it on in about 45 minutes without putting the Highlander on jackstands. I did it alone and found a scissor jack the perfect means to elevate and support the passenger's side while I attached the driver's side. It seems to go better by attaching one bolt on the driver's side then one on the other side. By the way, your video explains how the washers should go on. The written instructions accompanying the hitch did not. The wiring package did not follow the video OR the written instructions. Both state that the package contains double stick tape that should be used to connect the black box. There was no tape in the package or attached to the black box. I wedged the black box in an open in the body. I think it will be secure and the wire protected from rubbing. Otherwise, i will have to open the compartments up again and apply adhesive of my own. Your video suggested that the wires can be lead from the driver's side connectors to the equipment tray in the back. It can, but the wires are pinched between the plastic body part. Over time, I suspect wire sheath would rub away and ground the connection. I ground away a very small section of the equpment tray. It created enough space to relieve the pinching. By the way, I'm 66. I'm sure kids could install the hitch even faster than I did.

Trailer hitch looks great, will work great this spring for trailer hauling projects.

Needed a class III Ball Mount and Susan from etrailer.com provided excellent customer service skills helping me pick out the correct one for my Highlander. It fits great, is secure, and tows my trailer with no problem. Thanks, Susan!

To be honest, I use it upside down. I needed a hitch with rise, but none were available at time of purchase, and yours, inverted, works perfectly! The welds are regularly checked and remain all secure. It's a good hitch.

Working in the sand and grass of my driveway my wife and I installed our new etrailer receiver hitch. Great fit and finish! Went right on as described in the online guide. Hitch required a spacer washer on top back bolt attachment point. Taped it on so it would not move while lifting in place and it stayed right there! Used a car jack to raise up and hold the hitch into the underside of the trunk tighten the bolts and reattached the tail pipe done. Now we can pull our Sunfish Sailboat any where the car will go.

Yes Laura its a good thing. But I do dismount it when not in use lest I smash someones bumper when backing into a parking space. .

We sold our small motor home and purchased a small travel trailer. This hitch provided a perfect solution to how to use our bike rack while towing the trailer. It even allows room for the pickup tailgate to be lowered without removing the bikes from the rack. The hitch is very hefty with a high weight limit - plenty for the GVW of the trailer (7,000#) plus 125# of rack and bikes.

Super solid mount at a great price. Just the right drop for my boat trailer.

Very pleased with etrailer. Very easy to order from website. Fast delivery, easy to install ,perfect fit . Thanks. .

My usage of your hitch is a bit unusual, I think. I pull a two ton roller with my Ram and I've used your cushioned hitch to smooth out the process. The roller Lunette just dropped over a 2" ball and then banged and jerked on the ball neck. Check out the photos for my adaptation.. I can flip it over and use the 2" ball! Have enclosed some photos. The cushion is holding up very well and it takes a beating!! Thanks

We have a Pink Tractor (google Mom's Pink Tractor) that we pull to events, mainly in Ks, Ok, Mo, and Ne. We have around 35 events a year we take the tractor to to promote breast cancer awareness. The other day my wife and I were leaving for an event, i had let a friend borrow the hitch to see how he liked it. In less then a mile from the house my wife started complaining about the trailer jerking. That is coming from a lady that really was upset when I paid that much for a hitch. She told me to stop and buy one. (a long and expensive trip, we had to stop at a casino so she could rest her neck) I could write a review with a lot of trailer talk, but, this story tells the story.

The biggest issue I have is that the video on the receiver said the rise can go up or down. I try to put the ball in the hole in the rise position and it does not seat all the way the way it does in the down position. Not sure if I can Seat by drawing down the nut or not .

Very happy with this ball mount - provides just the amount of drop we required for a level tow of our GeoPro travel trailer by our RAM2500. Plus, the extra length not only allows a tighter turning radius, but also allows us to lower the truck tailgate without having to detach the trailer. Huge improvement on all accounts for us compared to our prior setup. The product is well built and I'm confident will provide us years of good use.

Heavy duty , very good quality.

Haven't been able to break it yet.

I hooked up the draw bar today for the first time to the trailer that I built and the hitch I installed. The draw bar uses a cotter pin that slides on the bolt rather than going through a hole to mount the bar to the hitch. I have never used a sliding on pin in anything - I've only used those that go through a small hole matching the pin. This includes my farm tractor and other tools. I hope it is secure because it does slide on easily. The bar itself appears nice and strong.

Excellent product! With the three different ball sizes, this tri-ball mount gives you a lot of flexibility. Gone are the days of having several different ball mounts to fit different tongues. High quality construction makes this an excellent investment.

This item should solve the problem I have had with a stainless 3-way ball when I tried to reverse the position on the ball mount. The threads galled between the hex nut and hitch ball.

Works fine, maybe a bit too long of a drop for a 2022 Highlander Hybrid

Fast shipping

Purchased this hitch as a companion for our Reese anti sway control. The small ball for the Reese sway control fits in the bracket and the 2” drop on the hitch is exactly what we needed to have our Jayco camper level when towing.

Nice finish, hopefully will hold up over time. Unfortunately it is rather loose inside the 2" hitch hole, I don't understand how hard it is to get a tighter tolerance. We used some electrical tape as others suggested, but I would expect more from this brand.

Perfectly as described, Box was a heavy hitch and the box must have been damaged in shipping so it was a little delayed. You can't mess up a forged hitch it still is in excellent condition.

Looks to be a well built hitch there's virtually no other 12" drop hitches short of expensive adjustable ones it's just about right for my custom bumper

Arrived today. Fast shipping, and thank you for that! Seems to be a quality ball mount. Just what I needed to get the ball lower to tow my trailer. With this, now the top of the ball is at 16" where it needs to be. Custom built receiver on my old moving box van. Just need to weld on safety chain slots and paint it. Can't drop the lift gate with the receiver in (its pinned on both sides), but hey....I can tow now.

Retail type stores only carry mainstream items so when I needed a special length ball mount for my 2011 Traverse I found the size and quality with Curt Products .

Recently bought a Kubota RTV x900. The receiver is located under the bed. With the extra long ball hitch drawbar I can easily get to the drawbar and use a clevis to hitch my 5ft. wide mower or attach a ball and use the trailer. The pictures will illustrate the length of the drawbar which makes access very easy. The product is heavy duty and well made. Ordered this product on Thursday morning and it was delivered the next day, Friday afternoon. Customer service was helpful, will use etrailer again. Thanks

I've used the hitch over the last year on several trailers and loads. The adjustability made towing a much better feel and ride over a fixed hitch that at times not the greatest. I see no wear, very easy to adjust even once coupled to the trailer and finding the trailer needs to be leveled better.

Works flawlessly. I was very excited the day I got home and my Rapid hitch was on the front porch. It came in nice box and was packaged very well. I opened it up and unpacked my rapid hitch and I was very impressed with the quality and precision of this hitch. All of the machining was PERFECT and everything fit together right. I put it in my truck right away. Going down the road with the trailer on and off there is absolutely no rattles, clunks, or jolts. I also love how everything is aluminum or stainless steel, NO RUST. I wish I could've gotten the greaseless model but my boat is too heavy. My only complaint is that it doesn't come with locking pins. With a hitch this expensive I really wish it came with them. Do yourself a favor and order them with your rapid hitch so you don't have to pay for shipping in the future. Other than that great product and I believe it will outlast me.

We bought this to tow our 3,000 lbs. boat with our Subaru Ascent with a 5,000 lbs. towing capacity. With the OEM ball mount, we could really feel every jolt and jiggle from hard stops, going over bumps in the road, and trailering down dirt roads. However, the dual cushion ball has really improved our trailing experience. Once we get up to speed, we hardly notice we are towing our boat. It's also great because some of the lakes we visit are down dirt roads, and the cushion makes this a much more pleasant experience. I would highly recommend this to anyone towing a boat or larger trailer with a SUV as it maintains that comfortable ride and the jostling of the trailer is much less noticeable.

A year has passed with my Convert-A-Ball Dual-Cushioned, Adjustable Ball Mount and I have nothing but praise for this mount. Once you find the correct height to have a perfectly level trailer there's no need to adjust. The beauty lies in the cushioning! Towing a Yamaha AR190 (3200lb boat and trailer combo) is silent. Even over the bumpiest pavement the tow is smooth. There is no harsh slamming when braking or taking off from the boat ramp. I don't know why everyone isn't running one of these, I wouldn't run any other hitch mount PERIOD! If you're on the fence, get off and buy one, you will NOT regret it!