See what our Experts say about this Draw-Tite Trailer Hitch Ball Mount

• Is There A Fixed Straight Hitch For a 2" Receiver With a 2" Hitch Ball?
  A Tri-Ball mount like the MaxxTow # MT70021 is going to be the only style ball mounts we have with no rise. You can use the Draw-Tite Ball Mount # 2923 in the rise position with a 2" Ball # 63845. This will only sit 3/4" above the top of the receiver opening. It would be the closest we have to the Curt Towing Starter Kit # C45147 you found.
  view full answer...
• Which Trailer Hitch for 2021 Toyota Highlander XSE?
  The Curt # C99FR Class III hitch you mentioned would work great with your Highlander XSE. Keep in mind, if the vehicle is equipped with the What are you planning on using the hitch for? If you'll just use it for a hitch mounted accessory, all you need is the hitch. If you'll be using it for towing, you'll need a wiring harness, a ball mount and a trailer ball. For a wiring harness, what you'll use will depend on whether your vehicle is equipped with the factory tow package. If you DO have...
  view full answer...
• Trailer Hitch, Trailer Connector and Towing Accessories Suggested for 2020 Chevy Colorado
  A hitch is indeed available! I'd recommend the US made Curt Class III hitch, part # C13176. The hitch has a 8000 lbs towing/800 lbs tongue weight capacity, so it'll be able to handle any towing job you throw at it (as long as you don't exceed the towing capacity of the truck itself). If your truck doesn't already have a trailer connector, I'd recommend # HM11141144 which provides both a 7-way and a 4-pole connector. You'll also need a ball mount like # 2923 and # 19260 for a 1-7/8 or...
  view full answer...
• Can 2018 Toyota Highlander Use Ball Mount WIth 2-5/16" Ball
  If your question is can you use a ball mount with 2-5/16" ball with your 2018 Toyota Highlander Hitch, yes you can. More than likely you have a Class III hitch with a 2" receiver like the # e98844. This can use a ball mount that fits a 2" receiver like the # C45041 which has a 2-5/16" ball and a hitch pin and clip. If you are referring to your ball mount, or draw bar, like the Draw-Tite Ball Mount for 2" Hitches # 2923 then you need to match the shank size to the ball hole diameter. This...
  view full answer...
• Drop Ball Mount for Subaru with Rockerball that Needs 0 Rise/Drop
  Since your suspension would sag a little bit with the weight of your trailer I would go with a slightly higher ball mount around 1 inch drop in conjunction with a Rockerball part # C40047 and you'd be set. If you have a 1-1/4 inch hitch you'd want the part # 36051 or a 2 inch hitch # 2923.
  view full answer...
• Can Draw-Tite Ball Mount 2923 Give 3/4 Inch Rise
  Yes you can; flipping the Draw-Tite Ball Mount # 2923 upside down will give you the 3/4" rise you are seeking. It comes with a pin and clip so for a hitch ball you will need - depending on your trailer's coupler - either 1-7/8" Hitch Ball # C40002, 2" Hitch Ball # 40038, or 2-5/16" Hitch Ball # C40005.
  view full answer...
• Will the Softride Dura Folding Bike Rack fit a Curt # 13354 Hitch on a 2007 Acura MDX
  The Softride Dura, part # SR26247 will fit the Curt Hitch, part # 13354 just fine. You will need to take one measurement however, to make sure the bike rack comes out far enough to clear the bumper. Measure from the hitch pin hole, straight out to the furthest point of the bumper. As long as this measurement is 6 inches or less, the bike rack will fit. At the bottom of the Dura page, you will see a few dimensional diagrams that will help you get an idea of how it will fit on your MDX....
  view full answer...

Do you have a question about this Trailer Hitch Ball Mount?