Will the Draw-Tite Ball Mount # 2923 Work on a 2024 Tesla Model Y with the Tow Package?

Question

Question:

Will this work for a 2024 Tesla Model Y with Towing package ? Thanks

asked by: Howard

0

Expert Reply:

Hello Howard,

Thanks for writing in! I'm glad you found us, again =)

Yes, the Draw-Tite ball mount # 2923 will fit your 2024 Tesla Model Y with the factory towing package since it uses a standard 2-inch hitch receiver. The main thing to verify is whether the 2-inch drop or 3/4-inch rise will keep your trailer level while towing.

To check that, park both the Tesla and trailer on level ground. Measure from the ground to the top inside edge of the hitch receiver on the Model Y. Then measure from the ground to the bottom of the trailer coupler where the hitch ball sits when the trailer is level. If the coupler measurement is lower than the receiver height, you’ll want a drop. If it’s higher, you’ll want a rise.

For example, if the receiver height measures 18 inches and the trailer coupler measures 16 inches, the 2-inch drop on # 2923 would be a great match. If the coupler sits slightly higher than the receiver, you can flip the ball mount over and use the 3/4-inch rise position instead (please refer to attached image).

For a hitch ball, a great option is the etrailer 2-inch Hitch Ball # 63845. It has the correct 1-inch diameter shank to fit the ball mount and a 7,500 lb weight capacity that matches well with # 2923 for most small trailers, utility trailers, and lightweight campers.

What kind of trailer are you planning to tow with your Model Y?

expert reply by: Kate F

0

Ball Mount as Rise
(click to enlarge)

Howard

5/13/2026

Thanks Kate! It’s a U-Haul 4x8 trailer. Do you have a lock for the unit as well?

Kate F.

5/13/2026

@Howard We have some great options for you: The Anti-Rattle Trailer Hitch Receiver Lock for 2" Hitches, 3-1/2" Span # 63232 is a great option. It will function as a lock while also helping reduce movement and noise in the hitch. If you’re just looking for a standard locking hitch pin, the etrailer Hitch Receiver Lock for 2" and 2-1/2" Hitches, Flush, 3-5/8" Span, Chrome # e98881 will work well. U-Haul trailer couplers typically sit around 18" high. To make sure you get the right ball mount for level towing, I recommend measuring from the ground up to the inside top of your hitch receiver on your 2024 Tesla. Once you have that measurement, let me know and I can help you dial in the best rise or drop needed.

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

You can use the RV Propane Gas Detector #RS64FR (white) or #RS44FR (black) to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Will the Draw-Tite Ball Mount # 2923 Work on a 2024 Tesla Model Y with the Tow Package?

Featured Help Information

Miscellaneous Media

Continue Researching