See what our Experts say about this CURT Trailer Hitch Ball Mount

• Recommended Euro-Style Ball Mount for a 2015 Nissan Altima with Curt Class I Trailer Hitch
  The recommended 2 inch Euro style ball mount for Curt trailer hitch # C11352 on a 2015 Nissan Altima is # C45572. I went out to the warehouse and pulled one to take some measurements. From the center of the pin hole to the part of the shank where it starts to bend up is 3 inches. This will work because the rear bumper on the Altima tapers upward above the hitch receiver. At 6-1/2 inches out from the center of the hitch pin hole, where the shank starts to bend straight up, it is at a height...
  view full answer...
  
• Recommended Euro Style Drawbar with 7 Rise
  I may have a solution for you, but we don't have any Euro style drawbars with a 7" rise and after doing some digging I'm not quite sure they are available that tall . With that said, you may be able to use the Curt # C45591 which has a 5-1/8" rise. This would be the closest solution to the 7" you're looking for. If you were willing to use a non-Euro style draw bar, you could use the Brophy # BM96, which has a 5" rise from the top of the shank to the top of the ball mount platform. You...
  view full answer...
  
• Ball Mount for 1-1/4 Inch Receiver With 50mm Hitch Ball
  The Curt Class II Euro Style Drawbar with 1-7/8" Ball # C45591 will fit a 1-1/4 inch trailer hitch receiver and secure to the hitch with Pin and Clip # F-4 but I wouldn't be able to tell you if it will fit a European trailer. It has a 1-7/8 inch hitch ball so it's not exactly the same size as a 50mm hitch ball. That said we do offer a 1-1/4 inch ball mount and 50mm hitch ball that will fit together: - Draw Tite Drawbar for 1-1/4" Hitch # 36053 The Draw-Tite does come with a pin and clip...
  view full answer...
  
• Can I Tow a U-Haul Trailer with My 2017 Kia Soul
  Since the Class I Curt Trailer Hitch Receiver # C11419 for your 2017 Kia Soul can tow up to 2,000 lbs it will be able to handle the weight of either trailer, but the 1,650 lbs and 1,800 lbs weight ratings you're seeing is the max amount of cargo each trailer can hold. When you add the weight of the trailer into the mix you're then looking at 2,500 lbs for the 4x8 and 2,700 lbs for the 5x8. As long as you stay under the 2,000 lb weight capacity of the Curt hitch you'll be fine. This means...
  view full answer...
• Looking for a 50mm Trailer Hitch Ball
  We do have some 50mm balls: # 63912 # EH53C-C # 337RB50MM The bigger issue you are likely to run into is the electrical requirements of a European trailer versus one for the US market. In Europe they have separate circuits for all the lights on a trailer. Here in the states we have one circuit for both left brake light and turn signal, one circuit for both right brake light and turn signal, one circuit for all running/tail lights, and one ground. Five, 6, and 7-Ways have additional circuits....
  view full answer...
• 2" Euro Style Ball Mount Hitch With Tallest Rise
  Sorry it took so long to get back with you Rob. I had to investigate this as we do have the 2" # C45592 version of the 1-7/8" # C45591 Euro ball mount. The 1-7/8" you found was incorrectly measured to the top of the ball which is why the rise was different at 6-5/8" than the 2" at 5-1/8" to where the ball is attached to the mount at the bottom. These are also the largest amount of rise we offer in a euro style ball mount.
  view full answer...
• Recommended 1-1/4 Inch Draw-Bar w/ a 6 Inch Rise
  There is only one drawbar for a 1-1/4" hitch receiver that has a 6" rise. It is the Curt Class II Euro Style Drawbar item # C45591. This is a European style ball mount where the hitch ball is attached. It will give you 6-5/8" of rise. This is only recommended to be used on class II 1-1/4" receivers. If your hitch is a class one then the most rise you can get is 5-1/2" with the Brophy Anti-Rattle Drawbar item # BR39FR. For hitch balls you will want item # 19258 for a 2 inch ball or item...
  view full answer...
• Parts to Transport Mobility Scooter With a 2006 Hyundai Sonata
  It looks like the only hitches available for your 2006 Hyundai Sonata have a Class I rating so you're going to need to use a trailer to transport the scooter as opposed to a hitch-mounted lift. This is due to the 200 lb tongue weight rating of the hitch itself which, to my understanding, the scooter would already be pushing the limits for. If you're interested in going this route then I recommend using the following parts: Curt Trailer Hitch Receiver - # C11325 Curt T-Connector Wiring...
  view full answer...
• All Parts Needed to Tow U-Haul Trailer With 2011 Hyundai Sonata Non-Hybrid
  Appreciate that info and we can go ahead and get you all the parts you need, including the ball mount, to tow the U-Haul trailer with your 2011 Hyundai Sonata non-hybrid. I'll go ahead and list them for you below: - Curt Trailer Hitch Receiver # C11025 - Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # C56049 - Curt Class II Euro Style Drawbar with 1-7/8" Ball - 5-1/8" Rise # C45591 - Hitch Pin and Clip # F-4 Both the hitch and wiring harness are fits for your '11 Sonata,...
  view full answer...
• Parts Needed to Transport Scooter and Wheelchair with 2015 Chevy Camaro
  If your 2015 Chevy Camaro is a convertible you'll need the Curt # C11222 but if it's the Coupe you'll need the part # 24850 instead. These will fit if your Camaro does NOT have the Grounds Effects Package. I also looked up the owner's manual for a '15 Camaro and Chevy says not to tow with the ZL1 or Z/28. If you have either of those or the Ground Effects Package then you unfortunately won't be able to accomplish this goal with this specific vehicle but if none of these apply to you keep...
  view full answer...
• Is There A Hitch Available For A 2017 Toyota Camry That Can Handle 500 Pounds Of Tongue Weight?
  The trailer hitches offered for your 2017 Toyota Camry will all be Class 2 rated hitches. There can be a little variance with max capacity in this class and the highest rated one is the # C12107, offered by Curt. This is a custom fit hitch and will have a pretty easy install (see attached video), but this will have a max tongue weight of 350 pounds (which is the highest Class 2 hitches go up to). Unfortunately, there is not a way to get a hitch with more tongue weight than this, and, to...
  view full answer...
• Recommended Trailer Hitch Receiver, Ball Mount and Wiring For a 2013 Chrysler 200
  With the Curt Trailer Hitch Receiver # C11133 on your 2013 Chrysler 200, Curt recommends using one of the following ball mounts. First is the Curt Class II Drawbar # C45522 with either a 1-7/8" Ball # C40001 or 2" Ball # C40018. Or you can choose one of their Euro Style Ball Mounts with a 1-7/8" # C45591 or 2" # C45592 ball. Whichever you choose you will need a Curt Hitch Pin and Clip # F-4 to secure it in your receiver. You will also need a Vehicle Wiring Harness # C56211 to control...
  view full answer...
• Does Curt Trailer Hitch for 2000 Lincoln Town Car Come with the Mounting Hardware
  Yes, all of the hardware needed for installation is included with Curt trailer hitch # C12130. If you plan on doing some towing you can use the nifty Curt Euro ball mount # C45592 for a 2 inch ball or # C45591 for a 1-7/8 inch ball. And for trailer wiring you can use # C59496 to add a 4-Way flat to the rear of the vehicle.
  view full answer...
• Which Will have Better Ground Clearance Ball Mount C45510 or Euro Drawbar C45591
  Curt Class II ball mount # C45510 will actually be a little better with ground clearance compared to Euro drawbar # C45591 because it doesn't stick out as far and does not have as much of the steel shank below the ball.
  view full answer...
• Euro Style Ball Mount Recommendation for Draw Tite Hitch on 2001 Honda Odyssey
  For a Class II Euro style ball mount that would work well with your Draw Tite hitch part # 36417 we have the part # C45591 for a ball mount with a 6-5/8 inch rise which would work well. Or we have the part # C45571 which has a 2-5/8 inch rise. Both of these have 1-7/8 inch balls.
  view full answer...
• Compatibility of Anti-Rattle Device with Bike Rack Secured by a Hitch Ball
  Curt Class I trailer hitch # C11406 is confirmed to fit properly on your 2016 Honda Fit. However, the hitch I recommend instead is the Draw-Tite # 24920. This hitch installs identically and has the very same capacity, but it costs less and does not have the requirement of using the support strap # 18050 which Curt specifies for maintaining the warranty on your hitch when it is used with a non-trailer load like a bike rack. My contact at Thule confirmed that they used to offer a hitch-ball-mount...
  view full answer...
• Ball Mount Recommendation for 2012 Chevrolet Cruze With 1-1/4 Inch Trailer Hitch
  We have a couple different style ball mounts that will work with the hitch on your Cruze. For a standard ball mount I recommend the Curt, part # C45522. This ball mount has a 3-7/8 inch rise to help provide a bit more ground clearance. For a 1-7/8 inch hitch ball I recommend part # C40001, and for a 2-inch ball I recommend part # C40018. If you like the looks of the Euro ball mounts I recommend part # C45592 that comes with a 2-inch hitch ball and I recommend part # C45591 for a 1-7/8...
  view full answer...

Do you have a question about this Trailer Hitch Ball Mount?