Are Stallion Aluminum Car Hauler Ramps Available Individually

Question

Question:

Hi, Is this ramp available individually instead of in a set? Stallion 288-07489 Thanks

asked by: Eric

0

Expert Reply:

The # 288-07501 is only available as a set from Stallion with no options for the individual ramps. Depending on your needs, they do have another 48" ramp available individually which is the # 288-07474. This ramp is 48" long x 11" wide and has a weight capacity of 800 lbs.

expert reply by: Robin H

0

Answer 1

I have a solution for you. As far as the load rating of the single Stallion Loading Ramp - Steel - 48" Long x 11" Wide #288-07474, it has a weight capacity of 800 pounds. However, when you use the ramp as a pair like the 2 that come with…

view full answer...

Answer 2

In regards to loading ramps like the Loading Ramp part #288-07474, the length includes the lip/tabs on the top or bottom.

view full answer...

Answer 3

Yes, these 48 inch long ramps part #288-07474-2 would do a great job to get your riding lawn mower into your shed which is approximately one foot off of the ground. These will have more than enough capacity, will have great traction due to the mesh…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Are Stallion Aluminum Car Hauler Ramps Available Individually

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching