Bolt Size to Install Draw-Tite Class III Trailer Hitch 75237 on 2005 Toyota Sienna

Question

Question:

Do you have the exact specs for the bolts used to connect the hitch? I have tried spraying the nuts welded into the frame with WD40 and cleaning with a wire brush but still cant get all the bolts in 3 are in, 2 are started but I cant get in any farther and 1 I cant even start. I want the specs so I can try using a tap to clean out the threads of the nuts in the frame. Thanks.

asked by: Brad

0

Expert Reply:

According to the instructions, the bolts for hitch part # 75237, are M12 x 1.25 x 40MM bolts. If you do not have a metric tap and die set, I would just take one of the bolts to a hardware store and match the tap to the bolt.

expert reply by: Patrick B

0

Gene

6/17/2020

Is it possible to just purchase the replacement bolts/washers for this hitch? If yes, how much is it and where can I purchase it? Thanks!

Reply

Chris R.

6/21/2020

Yep! For replacement hardware you can use part # RHK. Once on the product page you'll just type the model number (75237) inside the text box and select "Draw-Tite" from the manufacturer drop-down menu. We'll then sent out the complete hardware kit for that particular hitch. Pricing info is located on the product page too.

Reply

Answer 1

For your 2009 Toyota Sienna, I recommend the Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" #C13105 you referenced. From the lowest point of the hitch receiver you will have about 8-1/2 inches of ground clearance. The inside top of…

view full answer...

Answer 2

The 2019 Toyota Sienna is a low ground clearance vehicle so there isn't much that can be done about a hitch like the etrailer Trailer Hitch Receiver part #e98837 scraping or bottoming out. That said, you can protect the hitch with an option like…

view full answer...

Answer 3

I will be glad to help you with your hitch selection. The Draw-Tite Class III 2 Inch Hitch #75237 would be an excellent choice for the towing situations you have described. With the 2 inch receiver you will have a wider selection of accessories…

view full answer...

Answer 4

The trailer hitch that is the best option for a bike rack for your 2012 Toyota Sienna is going to be the etrailer hitch as it offers the best combination of bumper and ground clearance as well as easiest install; the best hitch is going to be the…

view full answer...

Answer 5

Hey Daniel thanks for all the questions! One of them is going to be pretty easy but also disappointing, every hitch for your 2019 Toyota Sienna is going to require the panel to be removed, trimmed, then reinstalled. This is actually not as hard to do…

view full answer...

Answer 6

I do have a trailer hitch for your 2010 Toyota Sienna but the one for a Toyota Venza will not fit as the vehicle's have a different rear subframe so the holes will not line up unfortunately. For your Toyota Sienna, I recommend using the Draw-Tite…

view full answer...

Answer 7

If you're looking for a class III trailer hitch for your 2007 Toyota Sienna, either the etrailer #e98837 is going to offer the most ground clearance. This is especially important when considering hitch mounted accessories like bike racks, cargo…

view full answer...

Answer 8

The distance from the bottom of the #75237 trailer hitch to the ground is approximately 7-1/4 inches. Please keep in mind these dimensions can vary based on the suspension or tires and wheels that are installed on a vehicle, but on the model we…

view full answer...

Answer 9

In all likelihood you will not have to tap the holes on your 2006 Toyota Sienna to get the hitch bolts to fit. Usually the issue is that the weld nuts on the vehicle will get packed with grime and corrosion and all you will have to do is clean them…

view full answer...

Answer 10

You are correct that both the #e98853 and the #e98837 will both fit your 2018 Toyota Sienna L. There are a few noteworthy differences. One difference is that with the #e98853 the crosstube will be concealed behind the bumper. The crosstube on the…

view full answer...

Answer 11

There shouldn't be any factory bolts on the vehicle when installing Curt trailer hitch #13591. The hitch comes with the six M12-1.75 x 40mm bolts needed for installation (some installations only require 4 of the hex bolts). I have included a link…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Bolt Size to Install Draw-Tite Class III Trailer Hitch 75237 on 2005 Toyota Sienna

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching