How to Add Tension to Lippert Slide Topper Awning

Question

Question:

I’ve seen a previous question “answered” but it actually doesn’t answer the question. How do you tighten the slide awning after it’s installed?

asked by: David

0

Expert Reply:

To add more tensions to your slide topper, like part # LCV000163285, you'll need to remove the slide topper from your brackets and reroll the awning the 14 times the installation instructions call for. Also be sure your end caps are properly installed so the tension doesn't slip during operation.

expert reply by: Jon G

0

Answer 1

Currently we only carry either a 60" #FF60SW15ABL or one our our 40" #FF40SC15ABL or #FF40SW15ABL fireplaces. So this would require modification to your cabinet to replace your 48" wide Covenant fireplace WD914-48CT with one of our…

view full answer...

Answer 2

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Answer 3

You'll have to remove the roller tube on the Solera Slide-Out Awning #LCV000163285 and reroll the fabric and then reattach the roller to the arms. The manufacturer recommends rolling it completely back up and then unrolling it only one revolution…

view full answer...

Answer 4

According to Solara (Lippert), the correct number of turns to set the proper tension of their slide toppers like #LCV000163285 is between 12 to 16 turns, so I'd consider 14 to be a pretty good happy medium.

view full answer...

Answer 5

I reached out to my contact at Lippert to verify the procedure for loosening the tension on your slide topper awning. I have attached a link to the installation guide. On page 6 and step 11 is a description of releasing the awning tension. I have…

view full answer...

Answer 6

There are a few things you can try to tighten up your awning, but the tensioner will not have a manual adjuster, unfortunately. First, I suggest checking all your bolts and or screws to make sure they are all this tight. If they have loosened over…

view full answer...

Answer 7

To add tension to a slide topper like the Solera RV Slide-Out Awning #LCV000163285 you will want to remove the slide topper from the brackets and reroll the awning roller 14 times to add enough tension to the springs. The manufacturer suggest that…

view full answer...

Answer 8

To adjust the tension on your Solera RV Slide-Out Awning, #LCV000163285, you'll want to remove the slide topper from the brackets and reroll the awning roller 14 times to add enough tension to the springs. You'll also want to ensure your end…

view full answer...

Answer 9

With the Solera slide toppers we offer like the part #LCV000163285 the correct amount of tension is 12-16 turns before attaching the fabric to the rail.

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

How to Add Tension to Lippert Slide Topper Awning

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching