Owners Manual for the Draw-Tite Activator Brake Controller # 5504

Question

Question:

I bought my Hyundai 2009 Santa Fe used. There is no manual for the Draw-Tite Activator 5504 brake controller. How can I get one. This one is not the same as I had on a previous vehicle.

asked by: Kent M

1

Helpful Expert Reply:

I attached a link that has the installation instructions and owners manual for the Draw-Tite Activator Brake Controller # 5504 that you referenced.

expert reply by: Jameson C

1

Answer 1

To determine why you do not have any power on the blue brake output wire, I recommend starting at your brake controller. First, make sure the brake controller is on and receiving power. Most brake controllers have 4 wires, blue (brake output to…

view full answer...

Answer 2

Your Draw-Tite I-Stop IQ 20191 will only display the SH fault when the brake output (blue) wire isn't properly sensing a ground connection. This means if you cut the wire about 6" from the controller and test it with a circuit tester the…

view full answer...

Answer 3

The first step I suggest for troubleshooting your truck's trailer brake controller is to disconnect the truck and trailer and clean the connectors. If that does not correct the problem, test using a circuit tester like #PTW2992. See the linked…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Actually, the P3 now has the upgraded axis accelerometer like the P2. The Tekonsha P3 Trailer Brake Controller #90195, will work with both electric over hydraulic brakes on the trailer as well as electric brakes. It has a menu option on the display…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Hi Mike! Do you want a completely hidden hitch or one where only the receiver is visible? The Curt #C64NR you looked at has a concealed cross tube so you will only see the receiver hanging down at the rear. The Hidden Hitch by Draw-Tite #DT76GR will…

view full answer...

Answer 9

The trailer brakes work on a separate circuit than the lights. You have a couple of options to control the electric brakes on the trailer. One option is to use an air over electric brake control, #HA100400C. This unit connects to the air brakes on…

view full answer...

Answer 10

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 11

Since you have a 400ah lithium battery bank the best option is going to be the Redarc In-Vehicle BCDC Battery Charger #331-BCDC1240D. This DC to DC charger works with 12V or 24V vehicle systems with standard or smart alternators and is compatible…

view full answer...

Answer 12

Hey John, thanks for reaching out! If the 4-Way on your 1996 Ford F-150 is from the factory then the only wire splicing you'll need to do is with the Adapter #37185, which plugs into your 4-Way and then you'll connect the rest of the wires to…

view full answer...

Owners Manual for the Draw-Tite Activator Brake Controller # 5504

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching